You searched for: Tube Racks

Supplier: Bel-Art Products, a Part of SP

Chemical- and corrosion-resistant steel wire test tube racks are coated with heat-cured epoxy for long life and easy cleaning.

Supplier: Bel-Art Products, a Part of SP

Designed specifically for 5 mL centrifuge tubes, including Eppendorf® brand, this rack will also accommodate other tubes with a diameter of 13–16 mm.

Supplier: Bel-Art Products, a Part of SP

Unique tabs protect your samples from loss and contamination.

Supplier: Bel-Art Products, a Part of SP

Perfect for benchtop use or freezer storage, this double-sided polypropylene plastic rack accommodates 0.2 ml thin-walled PCR tubes on one side while the opposite side holds 1.5 ml to 2.0 ml microcentrifuge tubes.

Supplier: Corning

Microcentrifuge tube rack is molded from durable, autoclavable polypropylene, and features non-skid rubber feet.

Supplier: Bel-Art Products, a Part of SP

These white polypropylene racks are available in two popular grid sizes.

Supplier: Bel-Art Products, a Part of SP

This holder solves the problem of where to put a single 50 mL conical tube where it will not roll or spill.

Supplier: Bel-Art Products, a Part of SP

Tilt test tube racks to 25°, 35°, or 45°.

Supplier: Thermo Fisher Scientific

For incubation at elevated or reduced temperatures in water or ice baths.

Supplier: Bel-Art Products, a Part of SP

Molded from a special blend of polypropylene that is heavier than water, these racks sink to the bottom of the bath and will not tip over.

Supplier: Bel-Art Products, a Part of SP

Specifically designed for incubating 1.5 mL microcentrifuge tubes, this rack includes a hold-down disk to maintain a constant pressure on the tube caps and prevent them from opening during internal air expansion.

Supplier: Thermo Fisher Scientific

Racks are ideal for use below 4°C (39.2°F)

Supplier: Bel-Art Products, a Part of SP

Double-sided, compact polypropylene plastic racks are perfect for use on the benchtop or in the freezer.

Supplier: Bel-Art Products, a Part of SP

High-quality epoxy-coated wire racks in convenient extra-long sizes for volume test tube work.

Supplier: Thermo Fisher Scientific

These durable, brightly colored racks feature a three-tier design

Supplier: Bel-Art Products, a Part of SP

Incubate up to 24 microcentrifuge tubes in a water bath (choose from 1.5 mL or 0.5 mL size).

Supplier: Thermo Fisher Scientific

These polypropylene racks are molded in one piece and have a three-tier, grid design

Supplier: Bel-Art Products, a Part of SP

Polypropylene rack holds 143 vacuum-type syringe tubes: 80 tubes 12.7 mm (½") O.D. and 63 tubes 16 mm (⅝") O.D. up to 102 mm (4") long.

Supplier: Bel-Art Products, a Part of SP

This all-polypropylene rack provides efficient and extended cooling of twenty-eight 50 mL centrifuge tubes in a chilled bath.

Supplier: Bel-Art Products, a Part of SP

Rack emulates the 96-place format used in microplates, deep well plates, and other tools configured for drug research and robotic applications.

Supplier: Bel-Art Products, a Part of SP

Molded of steam autoclavable polypropylene, these racks fit 400 mL or 1000 mL beakers.

Supplier: Bel-Art Products, a Part of SP

Designed for preparing and storing 0.2 mL thin-walled PCR tubes and strip tubes before or after PCR sample processing applications.

Supplier: Bel-Art Products, a Part of SP

Made especially for use with beakers and waterbaths, these space-saving racks are ideal for small quantities of tubes and for use in cell culture laboratories.

Supplier: Thermo Fisher Scientific

Designed to hold 1.5mL microcentrifuge tubes and 1.2 or 2.0mL cryogenic vials

Supplier: Bel-Art Products, a Part of SP

Round holes with tight tolerances hold 13 mm tubes firmly for accurate processing, thus reducing lost samples and potential damage to instruments. Increased efficiency is achieved by using the numbered locations for programming, resulting in higher throughput.

Supplier: Bel-Art Products, a Part of SP

This 20 place polypropylene round floating rack fits most cryotubes and holds them tightly in a circular pattern formed by 12 outer and 8 inner openings.

Supplier: AZENTA US, INC

A 96-format frame that fits 8-well PCR tube strips with PC frame perfectly to allow for easy handling and use with automation.

Supplier: Bel-Art Products, a Part of SP

Attachment securely holds 1.5 mL microcentrifuge tubes in an 8 or 20 capacity disk for simultaneous vortexing.

Supplier: Corning

Microtube racks are available in three sizes and are designed to accommodate microtubes or screw-cap microtubes.
The 48-place aluminium rack holds 48 screw-cap tubes of all sizes. Unique ribbed-port design allows one-hand operation, supported by non-skid benchtop pads for a firm platform. Long-lasting aluminium construction. Centre support for added strength and stability.

Supplier: Heathrow Scientific

Slide these interlocking tube racks together in multiple orientations to work with different-sized tubes at the same time.