You searched for: Tube Racks

Supplier: Bel-Art Products, a Part of SP

This all-polypropylene rack provides efficient and extended cooling of twenty-eight 50 mL centrifuge tubes in a chilled bath.

Supplier: Bel-Art Products, a Part of SP

Height-Adjustable Racks securely hold up to six tubes or vials at any desired depth in a water bath or beaker.

Supplier: Bel-Art Products, a Part of SP

This innovative, split-frame rack holds up to two different size tubes (10–30 mm) in the same rack and allows users to quickly switch grids to hold other sizes as needed.

Supplier: Bel-Art Products, a Part of SP

These white polypropylene racks are available in two popular grid sizes.

Supplier: Bel-Art Products, a Part of SP

Molded of steam autoclavable polypropylene, these racks fit 400 mL or 1000 mL beakers.

Supplier: Bel-Art Products, a Part of SP

Rack emulates the 96-place format used in microplates, deep well plates, and other tools configured for drug research and robotic applications.

Supplier: Thermo Scientific

Supplier: Bel-Art Products, a Part of SP

Chemical and corrosion-resistant steel wire racks are coated with heat-cured epoxy.

Supplier: Thermo Fisher Scientific

Widely spaced holes and three-tiered design facilitate insertion and removal of tubes

Supplier: Corning

Microtube racks are available in three sizes and are designed to accommodate microtubes or screw-cap microtubes.
The 48-place aluminium rack holds 48 screw-cap tubes of all sizes. Unique ribbed-port design allows one-hand operation, supported by non-skid benchtop pads for a firm platform. Long-lasting aluminium construction. Centre support for added strength and stability.

Supplier: Bel-Art Products, a Part of SP

Chemical- and corrosion-resistant steel wire racks are coated with heat-cured epoxy.

Supplier: Bel-Art Products, a Part of SP

Chemical- and corrosion-resistant steel wire test tube racks are coated with heat-cured epoxy for long life and easy cleaning.

Supplier: Bel-Art Products, a Part of SP

Open-style floating rack provides tubes with maximum water contact and better circulation of the water bath around the tubes, allowing superior temperature control of the samples.

Supplier: Bel-Art Products, a Part of SP

The No-Wire™ racks fit neatly into round containers such as ice buckets and beakers, as well as desiccators.

Supplier: Thermo Fisher Scientific

These polypropylene racks are molded in one piece and have a three-tier, grid design

Supplier: Bel-Art Products, a Part of SP

Designed for high visibility, this 6-place, high-density polyethylene rack is end-supported by two columns.

Supplier: Thermo Fisher Scientific

Racks are ideal for use below 4°C (39.2°F)

Supplier: Bel-Art Products, a Part of SP

Specifically designed for incubating 1.5 mL microcentrifuge tubes, this rack includes a hold-down disk to maintain a constant pressure on the tube caps and prevent them from opening during internal air expansion.

Supplier: Bel-Art Products, a Part of SP

Double-sided, compact polypropylene plastic racks are perfect for use on the benchtop or in the freezer.

Supplier: Bel-Art Products, a Part of SP

Leave hands free for pipetting and other critical tasks with these polystyrene plastic tube holders that securely hold a 50 mL conical centrifuge tube.

Supplier: Bel-Art Products, a Part of SP

Molded from a special blend of polypropylene that is heavier than water, these racks sink to the bottom of the bath and will not tip over.

Supplier: Bel-Art Products, a Part of SP

This holder solves the problem of where to put a single 50 mL conical tube where it will not roll or spill.

Supplier: Bel-Art Products, a Part of SP

Round holes with tight tolerances hold 13 mm tubes firmly for accurate processing, thus reducing lost samples and potential damage to instruments. Increased efficiency is achieved by using the numbered locations for programming, resulting in higher throughput.

Supplier: Bel-Art Products, a Part of SP

Formed of steel wire with epoxy coating, this holder supports the conical bottom of a single 50 mL conical tube, as well as at a half height location.

Supplier: Bel-Art Products, a Part of SP

Incubate up to 24 microcentrifuge tubes in a water bath (choose from 1.5 mL or 0.5 mL size).

Supplier: AZENTA US, INC

A 96-format frame that fits 8-well PCR tube strips with PC frame perfectly to allow for easy handling and use with automation.

Supplier: Bel-Art Products, a Part of SP

The most versatile tube holder on the market, this set-up takes just seconds and gives users the choice of creating a 15 mL or a 50 mL tube holder.

Supplier: Bel-Art Products, a Part of SP

Attachment securely holds 1.5 mL microcentrifuge tubes in an 8 or 20 capacity disk for simultaneous vortexing.

Supplier: Bel-Art Products, a Part of SP

This 20 place polypropylene round floating rack fits most cryotubes and holds them tightly in a circular pattern formed by 12 outer and 8 inner openings.

Supplier: Heathrow Scientific

Each module is interlocked and adjustable with just a twist allowing to work with multiple sized tubes in the same rack