Supplier: Simport Scientific

Transparent adhesive sealing film is ideal for reducing cross contamination and/or spill over in PCR applications. 

Supplier: VWR Collection

Easier to apply and remove as compared to standard moulded PCR strip caps.

Supplier: VWR Collection

Polyester film, acrylic adhesive. These 49,5 µm thick polyester films minimise evaporation and prevent spillage and contamination between wells.

Supplier: Bohlender

Conical sealing ring made of static dissipative PTFE-EX.

Supplier: VWR Collection

Square well cap mats for sealing 96-well shallow or deep well plates.

Supplier: DWK Life Sciences

VMQ with bonded PTFE face.

Supplier: Avantor Fluid Handling

Extend the life and accuracy of your expensive and fragile instruments.

Supplier: VWR Collection

Easier to apply and remove as compared to standard moulded PCR strip caps.

Supplier: DWK Life Sciences

Silicone, translucent.

Supplier: IDEX RHEODYNE

Rotor seals are the common wear part in all the Rheodyne® valves and many can be purchased separately or as part of a RheBuild® kit.

Supplier: VWR Collection

These heat resistant 74,9 µm thick films are designed for thermal cycling applications. Polypropylene films are not pierceable. For PCR applications, where piercing with pipette tips or robotic probes is required for product recovery, use aluminium foil films. For real-time PCR applications, where maximum optical clarity is required, use optically-clear polyester films.

Supplier: Simport Scientific

Adhesive sealing films reduce sample-to-sample or well-to-well contamination and/or spill over. SecureSeal™ has the differential advantage of perforated end tabs and a multiple split backing which allow for easier and more accurate positioning and more secure sealing. The polyester based film with acrylic adhesive is inert and thus compatible with almost all microplate procedures. SecureSeal™ is less than 0,001% moisture permeable under high humidity conditions and less than 0,01% oxygen permeable.

Supplier: VWR Collection

Polyester film with acrylic adhesive. These non pierceable films in sheeted-roll format are recommended for ELISA tests, general incubation and short-term storage.

Supplier: VWR Collection

VWR®, Microplate seal, Cap strip, Single sheet/mat/strip, Cap strip for PCR plates and tube strips, dome, Non sterile

Supplier: DWK Life Sciences

Ball joints without ground joints only seal via the sealing ring.

Supplier: VWR Collection

Aluminium foils, 75,7 µm thick, for use with 96 or 384 well plates. Fit inside the rim of raised rim plates. These foils have one partial width end tab. Available non sterile only.

Supplier: VWR Collection

Ultra-clean film designed specifically for the laboratory, which ensures sample purity and eliminates contamination.

Supplier: Avantor

J.T.Baker®, Microplate seal, Mat (24 wells), Single sheet/mat/strip, Capmat for J.T.Baker plate square well 24, Well top shape: Square, EVA, Transparent, Pierceable, Non sterile

Supplier: GLASWARENFABRIK KARL HECHT

This sealing material prevents the draining of blood samples. For sealing several hundred micro hematocrit capillaries.

Supplier: VWR Collection

These 77,5 µm thick polyester films provide secure sealing around every well, not just a cover, thus minimising evaporation, preventing spillage and well-to-well contamination, and eliminating 'edge effects' in sensitive ELISA assays. Polyester films can also be used with cell culture plates for short-term storage, incubation, and containment of biohazards.

Supplier: VWR Collection

These films are 240 µm thick black vinyl with adhesive for use with 96-well, 384-well and 1536-well black microplates. They fit within the edges of raised rim plates and may be applied to either the plate top or bottom. The light blocking and absorbing properties of these films make them ideal for reducing stray light and crosstalk in fluorescence applications and for protecting light-sensitive samples in storage.

Supplier: VWR Collection

These films are 240 µm thick white vinyl with adhesive, for use with white microplates. Light reflective properties of the film, when used to seal clear bottom plates, maximise the sensitivity of bioluminescence and chemiluminescence assays in bottom-reading luminometers. White films have also been used as a backing matrix for microscopy of punch-out samples from filter plates.

Supplier: VWR Collection

A 139,7 µm thick hydrophobic porous film with medical grade adhesive for tissue culture plates, bio-blocks, and 96-well plates where gas exchange is necessary for cell or bacterial growth. These rayon films minimise cross-contamination, spillage and evaporation. They allow uniform air and CO₂ exchange for all wells, unlike plate lids which favour exchange for wells near plate edges. Sterile product is packed in tamper evident bags of 25.

Supplier: VWR Collection

These 106,7 µm thick vinyl films with 20 µm adhesive layer are designed for temporary protection of samples in 96-well plates from contamination and evaporation.

Supplier: Bohlender

FEP. Sealing for flat flange with groove.

Supplier: VWR Collection

Identical to polyester films above, but include a colour dot and white writing area on each end tab for plate identification. End tabs with backing removed adhere to the ends of the plate and are perforated so they can be left in place even if the centre portion of the film is removed. Alternatively, one inscribed colour-coded end tab can be removed and pasted in a laboratory notebook while the other remains on the plate.

Supplier: VWR Collection

Transparent polyester films with strong, non absorbing, non fluorescing, medical grade adhesive for superior performance in qPCR applications. Supplied non sterile.

Supplier: Avantor

Suitable to use with J.T.Baker® Plate Round Well 43001-0010, 43001-0016 or 43001-0116.

Supplier: EPPENDORF

Ensure airtight sealing of your PCR plates with Eppendorf® PCR films and foils. Tailor your choice to your assay needs, like the Masterclear® real-time PCR film, optimal for qPCR with its superior optical characteristics, or heat-sealing options for the best evaportion protection.

Supplier: COWIE

Mechanical Seals, Shaft guide replacement PEEK seal for 8 mm shaft