You searched for: Fittings and Connectors

Supplier: UPCHURCH SCIENTIFIC

These female M6 adapters are made from PEEK, EFTE or PCTFE.

Supplier: UPCHURCH SCIENTIFIC

LuerTight™ fittings are designed for connecting fluoropolymer tubing without barbs or nuts. By integrating ferrules into the Luer bodies, these fitting reliably hold tubing in place while giving the convenience of a Luer connection.

Supplier: UPCHURCH SCIENTIFIC

Ultra high performance fittings are manufactured from a proprietary PEEK blend (PK) which allow them to be used at higher temperatures (up to 200 °C) and higher pressures.

Supplier: VICI JOUR RESEARCH

One-piece hex-head fittings made from PEEK are easy to use with the ValvTool and the Color-It Color-Coded Fingertight adapters. The 10-32 thread is suitable for standard high-pressure female connections. They are available both in a short and long version.

Supplier: UPCHURCH SCIENTIFIC

These PEEK adapters make connections to female ¹/₈" and ¹/₄" National Pipe Thread (NPT) ports.

Supplier: UPCHURCH SCIENTIFIC

PP, ETFE or PEEK. The barbed inserts of the swivel barb adapters spin freely from the threaded nut in order to prevent the tubing from twisting during installation.

Supplier: UPCHURCH SCIENTIFIC

Designed for plumbing tubing through equipment housing. Each union has unique ³/₈-24 external threads and comes complete with a stainless steel nut and lock washer to hold it in place.

Supplier: UPCHURCH SCIENTIFIC

Reusable fittings made from stainless steel and proprietary PEEK polymer blend. Reusable up to 10 cycles without tubing damage or impact on pressure holding ability or carry-over (5 cycles if tightened to 1,6 N.m). Pressure rating up to 30 000 psi (2070 bar). Required torque 10 in-lbs (1,10 N-m)/14 in-lbs (1,6 N-m).

Supplier: VICI JOUR RESEARCH

PEEK flangeless nuts in combination with the inverted ferrule do not require flanging tools. A hand tightening procedure makes leak free seals. The inert ETFE ferrule is the only part, besides the tubing, which is in contact with the fluid, the nut is never in contact with the fluid stream.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® quick connect Luer adapters provide the opportunity to adapt either a female Luer or male Luer connection to a threaded connection. Conform to ISO requirements for medical Luer taper configuration and performance (45 psi/3,1 bar).

Supplier: SEMADENI

Hose connector, PE-HD, D = 9 mm

Supplier: SEMADENI

Connectors, Y- shaped, made of PP, natural color.

Supplier: GILSON

The Gilson safe aspiration station Y-shaped tubing connector is for use with the Gilson safe aspiration station.

Supplier: SEMADENI

PP, gray.

Supplier: VARIAN

Biocompatible adapter, 1/16” to 1/8”, PEEK, with fittings, PEEK

Supplier: Restek

A critical orifice in the EZ No-Vent® connector minimizes the amount of oxygen allowed into the MS source, eliminating the need for purge gas required. This enables to skip the lengthy vent and pump-down cycle.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, P-116, plug for micro fittings, PEEK, Black

Supplier: VICI JOUR RESEARCH

These fittings are designed for 360 µm tubing (metal, fused silica, PEEK or fused silica).

Supplier: VICI JOUR RESEARCH

These PP adapters are used for colour coding different solvent lines. They turn ¹/₄" hex-head nuts into fingertight fittings.

Supplier: UPCHURCH SCIENTIFIC

These fittings eliminate loosening due to tubing twist.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® MicroTight®, F-126S, fitting, standard micro knurl, PEEK red, 6-32 coned port, for 1/32" OD tubing, 5000 psi, PEEK

Supplier: VICI JOUR RESEARCH

These stainless steel 316 tees and crosses are ideal for joining solvent lines.

Supplier: VICI JOUR RESEARCH

Polyacetal flangeless nuts in combination with the inverted ferrule do not require flanging tools. A hand tightening procedure makes leak free seals. The inert ETFE ferrule is the only part, besides the tubing, which is in contact with the fluid, the nut is never in contact with the fluid stream.

Supplier: VICI JOUR RESEARCH

VICI Stainless Steel Unions are made for joining two pieces of ¹/₁₆" Ø tubing, or an ¹/₈" tube. They are precision machined with a focus on the concentricity of the bore as well as on the finish of the surfaces to give an absolute leak-free connection. These Unions have internal threads, which we recommend for most applications. Internal threads make stronger connections and internal fitting details provide the lowest dead volume for high performance instrumentation.

Supplier: DWK Life Sciences

Hose connector, 13-425

Supplier: SEMADENI

Connectors, Y-shaped, made of POM, white.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, Connector, tubing, P-801 barbed connectors for use with 1/16” I.Ø tubing, PP

Supplier: SEMADENI

Tubing connector, made of HDPE, with taper ends.

Supplier: OMNIFIT

Connector, 2-way, 0,8 mm bore

Supplier: SEMADENI

PP, translucent.