You searched for: Fittings and Connectors

Supplier: EDWARDS HIGH VACUUM METTLER

Reducing pieces made of stainless steel.

Supplier: Restek

A critical orifice in the EZ No-Vent® connector minimizes the amount of oxygen allowed into the MS source, eliminating the need for purge gas required. This enables to skip the lengthy vent and pump-down cycle.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, P-245, flangeless fitting for 1/16" OD tubing, PFA natural/ETFE blue, 1/4-28 flat-bottom port, standard knurl

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, P-116, plug for micro fittings, PEEK, Black

Supplier: VICI JOUR RESEARCH

Plugs can be used to close off an unused port in a valve or manifold. Size ¹/₄ - 28".

Supplier: VICI JOUR RESEARCH

PEEK one-piece fingertight fittings. 10-32 threads, for 1/16" tubing. Fingertight up to 350 bar (5000 psi).

Supplier: VICI JOUR RESEARCH

Fiberglass reinforced PP with PP washers. A number of chromatography systems still require or prefer flanged connections. When the tubing is flanged, the washer never comes in contact with the mobile phase.

Supplier: VICI JOUR RESEARCH

These PEEK adapters connect standard LC fittings to standard LC ports, usable with most common organic and inorganic HPLC solvents without risking corrosion, metal contamination, or protein degradation.

Supplier: OMNIFIT

Flanged tubing system is used for economical low pressure connection. A flanging washer is placed between the flange and the fitting nut. When screwed into a flat-bottom, the flange is compressesed against the bottom of the port to produce a seal.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, UH-427 VHP tee for 1/16" OD tubing, 10-32 coned threads, 0,50 mm thru-hole, 0,57 µl swept volume, stainless steel, Stainless steel

Supplier: UPCHURCH SCIENTIFIC

PEEK or stainless steel.

Supplier: VICI JOUR RESEARCH

These fittings are designed for 360 µm tubing (metal, fused silica, PEEK or fused silica).

Supplier: UPCHURCH SCIENTIFIC

One piece super flangeless fitting is ideal for those connections that need to be broken frequently and tubing assemblies because they swage onto the tubing.

Supplier: UPCHURCH SCIENTIFIC

PEEK polymer adapters connect peristaltic tubing to standard rigid or semi-rigid tubing.

Supplier: VICI JOUR RESEARCH

These PP adapters are used for colour coding different solvent lines. They turn ¹/₄" hex-head nuts into fingertight fittings.

Supplier: UPCHURCH SCIENTIFIC

These fittings eliminate loosening due to tubing twist.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® MicroTight®, F-124H, fitting, micro headless knurl, PEEK blue, 6-32 coned port, for 360 μm OD tubing, 5000 psi, PEEK

Supplier: UPCHURCH SCIENTIFIC

These adapters are made from PEEK or PTFE. Female to male 10-32 to 1/4-28 adapters.

Supplier: UPCHURCH SCIENTIFIC

Metric flangeless fittings offer the same benefits as flangeless fittings with the additional feature of being used for metric tubing and ports. They are specifically designed to connect 1,8, 2,0, 2,5, 3,0, or 4,0 mm Ext.Ø tubing to flat-bottom ports when paired with the appropriate M6, 1/4-28, or 5/16-24 flangeless nuts.

Supplier: VICI JOUR RESEARCH

These stainless steel 316 tees and crosses are ideal for joining solvent lines.

Supplier: UPCHURCH SCIENTIFIC

PEEK. Ideal for infusing samples into lab-on-a-chip devices. This product introduces only 14 nl of additional volume to the flow path. Use it to directly connect a Luer-tip syringe or other product that terminates with a standard male Luer to 360 µm ext. Ø capillary tubing without tubing sleeves. MicroTight® fittings are included.

Supplier: VICI JOUR RESEARCH

Polyacetal flangeless nuts in combination with the inverted ferrule do not require flanging tools. A hand tightening procedure makes leak free seals. The inert ETFE ferrule is the only part, besides the tubing, which is in contact with the fluid, the nut is never in contact with the fluid stream.

Supplier: VICI JOUR RESEARCH

VICI Stainless Steel Unions are made for joining two pieces of ¹/₁₆" Ø tubing, or an ¹/₈" tube. They are precision machined with a focus on the concentricity of the bore as well as on the finish of the surfaces to give an absolute leak-free connection. These Unions have internal threads, which we recommend for most applications. Internal threads make stronger connections and internal fitting details provide the lowest dead volume for high performance instrumentation.

Supplier: Lenz Laborglas GmbH & CO.KG

Connectors, made of PBT, red with integrated silicone (VMQ)-PTFE sealing.

Supplier: VICI JOUR RESEARCH

Ferrule, SS bushing, PEEK, For tubing ext.Ø: 1/32"

Supplier: EDWARDS HIGH VACUUM METTLER

Blanking flanges made of aluminium or stainless steel.

Supplier: UPCHURCH SCIENTIFIC

These fittings are made from stainless steel.

Supplier: EDWARDS HIGH VACUUM METTLER

Cross pieces made of aluminium or stainless steel.

Supplier: UPCHURCH SCIENTIFIC

PEEK or PCTFE.

Supplier: Restek

Graphite two-piece construction. For Shimadzu 17A, 2010, and 2014 GCs.