You searched for: Valves

Supplier: Restek

Mininert® valves are very convenient for repetitive sampling and limit content exposure to the silicon septum. The crimp-top valve for 20 mm ID glassware slides into the neck of the vial.

Supplier: Lenz Laborglas GmbH & CO.KG

DURAN®, borosilicate glass, clear. Prevent pressure loss or backflow. Simple design, cannot be dismantled.

Supplier: OMNIFIT

The high pressure manual rotary valves are made from PTFE with a PCTFE rotor with a bore size of 0,8 mm making them ideal for pressure applications up to 500 psi. They are available in four and five port versions. All ports are 1/4"-28 UNF flat-bottom and will accept any 1/4"-28 UNF male fitting. These valves are mountable using the pre-drilled M3 mounting holes.

Supplier: SEMADENI

Three way ball valve with PP body and PTFE tips with total length of 65 mm.

Supplier: UPCHURCH SCIENTIFIC

These standard inline check valves are made from gold plated stainless steel.

Supplier: UPCHURCH SCIENTIFIC

The 6-port medium pressure injection valves feature easy, external sample loop customisation. Simply clean-cut a piece of tubing that represents the volume of sample you wish to inject, taking into account the port-to-port volume of the valve.

Supplier: UPCHURCH SCIENTIFIC

Inline cartridge check valves are designed to limit flow in one direction and deliver a low cracking pressure. Ideal placement for these valves would be on the effluent side of the column to prevent post-column derivatisation agents from flowing back and poisoning the column if the HPLC mobile phase pump were to shut down.

Supplier: Restek

These metering gas valves reduce pressure between sample cylinder and GC injector.

Supplier: SciLabware

Designed for use in vacuum lines and fluid handling systems.

Supplier: QVF LABORTECHNIK

Air valve anti-return, cone size 14/23 NS, with sidearm, Borosilicate glass 3.3

Supplier: UPCHURCH SCIENTIFIC

These biocompatible PEEK and perfluoroelastomer inline check valves are designed for applications where low flow path volume is critical, such as delivery to lab-on-a-chip, single-cell analysis and micro- or nano-LC post-column derivatisation.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, V-101T 3-way flow-switching valve, bulkhead version, 1/16" OD tubing, 1,0 mm thru-hole, 9,7 µl swept volume

Supplier: UPCHURCH SCIENTIFIC

Pressure relief valves are ideal for preventing system over-pressurisation. These products protect system components by diverting fluid flow automatically when inline pressure exceeds the set limit.

Supplier: UPCHURCH SCIENTIFIC

For fine control of fluid flow rates, these valves can reduce outgoing flow. These needle valves are perfect for use with peristaltic pump fluid transfer applications, mass spectrometry and fraction collection. They can also be used to regulate gas flow in helium sparging lines and as a flow-dependent variable back pressure regulator.

Supplier: UPCHURCH SCIENTIFIC

Stop a flow stream quickly with these shut-off valves. The bodies are manufactured from either PEEK or ETFE. Both versions feature a PCTFE rotor, making them highly resistant to chemicals. The blue colorant used in some valve configurations has proven not to leach out with common HPLC solvents.

Supplier: VICI JOUR RESEARCH

This regulator installs on the detector drain line and prevents bubble formation in the flow cell during outgassing. It has an adjustable back pressure from 0 to 20 bar (15 to 300 psi) without disconnecting from the system. Other sizes available.

Supplier: Restek

Backpressure regulators can improve detector performance by preventing bubble formation in the detector flow cell. They also are useful in post-column reaction lines and between detectors and fraction collectors in preparatory work. Regulators are superior to more specific alternative solutions like small bore tubing, in which pressure varies with flow rate.

Supplier: UPCHURCH SCIENTIFIC

Back pressure regulator assemblies are designed to create incremental back pressures ranging from 5 to 1000 psi (0,3 to 69 bar). These biocompatible and stainless steel back pressure regulator assemblies are available complete with a replaceable, factory pre-set cartridge (except the 5 and 20 psi (0,3 to 1,4 bar versions).

Supplier: UPCHURCH SCIENTIFIC

These ultra-low volume back pressure regulators (BPRs) are developed to minimise swept volume, which is especially important for multi-detector applications.