You searched for: Fittings and Connectors

Supplier: Avantor Fluid Handling

Excellent choice to connect rigid tubing.

Supplier: Trajan Scientific and Medical

SilTite™, Replacement SilTite™ mini union ferrules, for 1/32" columns

Supplier: CPC COLDER

MPC Series couplings add ease of use and security to your most critical fluid handling applications.

Supplier: BURKLE

Universal thread adapter for nearly all drums and other containers with opening of 48 to 75 mm in diameter, regardless of the respective thread.

Supplier: Avantor Fluid Handling

Ultra-clean and reliable fittings for highly critical and corrosive chemicals.

Supplier: Bohlender

For vertical installation of b.safe funnels 130/180 on canister with inclined connectors and S60 thread. The insert made of static dissipative PE-EX is freely turnable inside the S60 screw cap (PPS) and thus allows vertical alignment of the funnel on the canister.

Supplier: Avantor Fluid Handling

Ideal for extremely corrosive materials—PFA will not rouge or pit.

Supplier: Bohlender

Made of glass-fibre reinforced PTFE.

Supplier: Avantor Fluid Handling

Convenience of a quick-disconnect in pressure and vacuum applications.

Supplier: Bohlender

Fitting made of PTFE, white.

Supplier: Trajan Scientific and Medical

These ferrules are made from 15% graphite and 85% Vespel®. They have a temperature limit of 350 °C and cannot be re-used with another capillary column.

Supplier: Bohlender

Tube end fittings with male thread and PA washers.

Supplier: Bohlender

Combination of capillaries and tubes of several HPLC systems in one desktop mount.

Supplier: CPC COLDER

Couplings allow rapid disconnect and reconnect with one hand and without the need for tools.

Supplier: Avantor Fluid Handling

Convenience of a quick-disconnect in pressure and vacuum applications.

Supplier: Bohlender

Black, screw cap made of PPS with GL thread and body made of PTFE with female thread UNF 1/4” 28G. The bottle neck is adjusted by an o-ring behind an elastic sealing lip.

Supplier: BURKLE

With the thread adapter made of high-quality stainless steel 1.4301 (304) a pump, a drain cock, or any other connection with thread G 2" (Whitworth pipe thread) can be screwed onto a container with G 1½" thread.

Supplier: Trajan Scientific and Medical

Vespel/graphite GC ferrules are made from quality polyimide/graphite blend. They seal with minimal torque and can be reused and repositioned along capillary columns if not over compressed in the fitting. Due to slight shrinking at high temperatures, they must be retightened after initial temperature cycles to avoid leaks.

Supplier: Saint Gobain Life Sciences

When it comes to retaining flexible tubing and hose onto barbed fittings, BarbLock™ retainers have become the standard in many industries because they solve inherent leak path problems in sensitive and demanding applications. The retainer uses no adhesives or solvents, is ideal for systems transferring delicate liquids or gases.

Supplier: Avantor Fluid Handling

Closed-system design ensures the safety of your environment and employees - at all phases of chemical handling.

Supplier: Bohlender

Three-part coupling consisting of coupling, locking nut made of PP and clamp ring made of FEP. To connect hard-walled corrugated tubing with the hose connection (NPT ¹/₈" thread) on b.safe waste caps. Locking nut with ergonomic gripping surface, additional grip hollows with SW10 on the coupling.

Supplier: Bohlender

Tubing distributors, body made of PTFE with nuts made of glass-fibre reinforced PTFE. One inlet and three or four outlets, bore diameter 6 mmutors made of fluoroplastic with glass-fibre reinforced PTFE nuts.

Supplier: CPC COLDER

NS6 Series couplings feature non-spill valves at a great price. Use the NS6 when even a few drops of spillage pose problems regarding safety, media cost or environmental regulations. These innovative couplings are lightweight, chemically resistant and easy to use.

Supplier: Avantor Fluid Handling

SterilEnz®-II/EC PP end caps are the only end caps that come equipped with a medical grade silicone gasket pre-attached to the fitting face. This feature prevents operators from misaligning or dropping gaskets during assembly. SterilEnz®-II/EC caps work with any standard flange gasket as well. Simply remove the pre-attached gasket (no tools required) and install your own.

Supplier: Trajan Scientific and Medical

Fixed outlet splitters for capillary columns
A fixed outlet splitter is recommended for splitting the flow from a capillary column between two detectors. The kit consists of a special Glass Lined Tubing (GLT™) splitter union, tubing and all ferrules required for installation.

Supplier: Bohlender

Two-part tubing coupling made of PP with PFA Fitting to connect capillaries with Ext.Ø. 3,2 mm. The passage with the integrated quick lock is tightly closed through loosening the coupling. Tubing connections are easily interrupted without dripping from the tube, tubes and removal flasks are tightly closed during exchange. Version and scope of delivery as per below chart.

Supplier: Trajan Scientific and Medical

Designed to be installed only with the force of your fingers delivering an easy, leak-free installation for capillary columns without the use of any tools. Developed with the unique, leak- and air-free properties of SilTite™ ferrules, which results in superior air tightness to reduce background noise in sensitive MS applications.

Supplier: CPC COLDER

NS4 series couplings feature non-spill valves in a compact size, at a great price. Use the NS4 when even a few drops pose problems regarding media cost or environmental regulations. These innovative couplings are lightweight, chemically resistant and easy to use.

Supplier: Trajan Scientific and Medical

Graphite ferrules are commonly used in GC systems on the inlet and detector ends because they don’t stick to the column, and can be removed and reinserted easily. They should not be used with GC/MS instruments because of permeability to air.

Supplier: Bohlender

Miniature distributors, made of PTFE, with female thread UNF ¼" 28 G, blockshaped, with holes for mounting (2×Ø 3,5 mm).