You searched for: Chromatography Supplies

Supplier: Agilent

MP-AES Sample Kits provide convenient kits for handling aqueous/acidic and organic samples. Select the appropriate one for your application.

Supplier: Agilent

A range of vacuum pump supplies is available to ensure the accuracy and performance of your ICP-MS vacuum system.

Supplier: Agilent

Purge valve actuator, For: 1120 pump

Supplier: Agilent

Agilent supplies are equivalent to PerkinElmer AA supplies, so you can be confident that they will integrate seamlessly with your PerkinElmer system.

Supplier: Agilent

Nitrogen phosphorus detector sample

Supplier: Agilent

These nebulisers for PerkinElmer AA systems provide the best precision, efficient drainage, minimal burner blockage, and reduced interferences.

Supplier: VARIAN

Mark 7 Spray Chambers for flame atomisation System. Easy-to-use twist and lock assembly allows for easy cleaning and routine maintenance.

Supplier: Agilent

CrossLab piston seal, reversed-phase, For: Thermo UltiMate 3000 RS and SD pump series

Supplier: Agilent

Nitrogen Chemiluminescence Detector (NCD) is a nitrogen-specific detector that produces a linear and equimolar response to nitrogen compounds based on a chemiluminescent reaction of NO with ozone.

Supplier: Agilent

A range of high quality supplies and components for the Integrated Sample Introduction System (ISIS) for use with the 7700 ICP-MS range.

Supplier: Agilent

These torches are suitable for PerkinElmer ICP-MS systems.

Supplier: Agilent

In 2005, Agilent released an improved FPD with minimum detectable levels (MDL) of 3,6 pg/s for sulphur and 60 fg/s for phosphorus. This is more than a five times improvement for sulphur.

Supplier: Agilent

Inert kit for ICP-MS enables analysis of high-purity and HF-containing samples using a PFA-based sample intro system with inert Pt or sapphire-injector torch.

Supplier: Trajan Scientific and Medical

SilFlow™ microchannel device (MCD) options for three-port GC splitters, four-port GC splitters and a Deans' switch MCD, perfect for multi-dimensional analyses. SilFlow™ can be incorporated into the system without impacting the chromatography.

Supplier: S.C.A.T.

The HPLC waste-sets, V2.0 are economical combinations for clean and safe disposal of liquid laboratory waste by HPLC systems or other analytical instruments. All sets consist of a canister and an original SCAT SafetyCap with exhaust filter as well as fittings, blind plugs and a tube connector.

Supplier: Merck

Merck columns come in three formats.

Supplier: Avantor

J.T.Baker®, Adapter, blue, for attaching reservoir or Luer tip to PP SPE columns

Supplier: Merck

SPME-GC inlet liners are designed for optimum sample introduction for specific injection techniques that are suitable for Agilent, Perkinelmer, Shimadzu, Finnigan, Varian and Thermo scientific equipped with split/splitless inlets.

Supplier: VWR Collection

ChromasterUltra Rs, ChromasterUltra Rs flow cell unit for 6430 diode array detector (path 10 mm, volume 2,2 µl)

Supplier: Merck

FocusLiner™ inlet liners are designed with wool plug to promote the rapid vaporisation of the entire sample, minimise mass discrimination, and prevent non-volatile material from entering the column. It incorporates a unique design to prevent the shifting of the wool plug during repeated injections or sudden inlet pressure changes. These liners are suitable for Agilent, Perkinelmer, Shimadzu, Finnigan, Varian and Thermo scientific equipped with split/splitless inlets.

Supplier: Merck

These SPME fiber assemblies can be reused for up to 100 analyses depending on the application.

Supplier: VWR Collection

Chromaster, Chromaster Plus HPLC interface control board for Chromaster Plus system control. USB cable and e-line cable (0,5 m) included, built into the autosampler upon installation in laboratory, if no autosampler is used, then the interface box (S) must be ordered instead

Supplier: Trajan Scientific and Medical

* Gas-tight.

Supplier: S.C.A.T.

These safety funnels and containers are used all over the world wherever the safe disposal of liquid waste is important. To ensure that collection points are also quickly ready for use, the most popular products have been assembled as sets. This requires only one part number for the comprehensive safety system, guaranteed compatible without time-consuming assembly of individual components.

Supplier: Trajan Scientific and Medical

The SGE inlet liner range aims to make it simple for all gas chromatographers to select the correct liner. Choosing the right inlet liner and injection parameters can increase peak areas and reduce detection limits by up to 300%.

Supplier: VWR Collection

This spare part is suitable for Chromaster 5210 and 5260 autosamplers. For Chromaster 5210 AS from Serial No. 1309-001 and 1309T-001 onward. For Chromaster 5260 AS from Serial No. 1205-001 and 1205T-001 onward.

Supplier: VWR Collection

Maintenance parts kit for Chromaster HPLC 5210/5260 autosamplers, type B. Kit contains 1× injection port seal 893-0810, 1× injection valve seal (PEEK) 893-0809, 1× syringe valve seal 893-0814, 1× syringe tip, 175 µl 893-0808

Supplier: VWR Collection

Syringe tip, 700 µl

Supplier: Bohlender

Integrate b.safe system caps and b.safe funnels in laboratory hoods or working tables. Liquid solvent waste can be lead directly into canisters via b.safe waste pipes.

Supplier: Trajan Scientific and Medical

The SGE inlet liner range aims to make it simple for all gas chromatographers to select the correct liner.