You searched for: Fittings and Connectors

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, U-650, replacement flangeless ferrule, ETFE natural, 1/2-20 flat bottom port, 250 psi, for 1/4" OD tubing, ETFE

Supplier: UPCHURCH SCIENTIFIC

PEEK polymer adapters connect peristaltic tubing to standard rigid or semi-rigid tubing.

Supplier: CADENCE SCIENCE

FLL to M5 × 6 mm thread (plated brass), Stainless steel, Thread: 0,125" NPT

Supplier: VICI JOUR RESEARCH

These fittings are designed for capillary LC, used in HTS techniques, proteomics, genomics, and other newer developments in industrial research requiring small sample size for reduction of analysis time, fittings and unions are easy to handle.

Supplier: ELDON JAMES

These tees are made of Natural Kynar® material, which has a temperature range of −62 to +107 °C and a pressure of 260 psi at 21 °C

Supplier: UPCHURCH SCIENTIFIC

PEEK.

Supplier: UPCHURCH SCIENTIFIC

These adapters are made from PEEK or PCTFE.

Supplier: OMNIFIT

Omni-Lok™ inverted cone fittings provide a simple, easy to use low-pressure connection. Only the ETFE cone is in the fluid path.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® MicroTight®, F-124H, fitting, micro headless knurl, PEEK blue, 6-32 coned port, for 360 μm OD tubing, 5000 psi, PEEK

Supplier: UPCHURCH SCIENTIFIC

PEEK or stainless steel.

Supplier: UPCHURCH SCIENTIFIC

These female M6 adapters are made from PEEK, EFTE or PCTFE.

Supplier: UPCHURCH SCIENTIFIC

PEEK, stainless steel or PCTFE.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® NanoTight™, F-142N, ferrules, ETFE natural, 10-32 coned port, for 1/16" OD tubing, 4000 psi, ETFE

Supplier: UPCHURCH SCIENTIFIC

PEEK.

Supplier: UPCHURCH SCIENTIFIC

ETFE or PEEK.

Supplier: UPCHURCH SCIENTIFIC

MarvelX biocompatible PEEK-lined stainless steel UHPLC connection system is easy to use and eliminates dead volume. It also provides higher repeat uses without sacrificing from consistent performance.

Supplier: UPCHURCH SCIENTIFIC

LuerTight™ fittings are designed for connecting fluoropolymer tubing without barbs or nuts. By integrating ferrules into the Luer bodies, these fitting reliably hold tubing in place while giving the convenience of a Luer connection.

Supplier: VICI JOUR RESEARCH

These stainless steel 316 tees and crosses are ideal for joining solvent lines.

Supplier: UPCHURCH SCIENTIFIC

NanoPort™ assemblies provide consistent fluid connections for chip-based analyses, connections will bond to a variety of substrate materials with the use of Loctite™.

Supplier: Bohlender

For connection of sensors with male thread PG to BOLA reactor lids.

Supplier: VICI JOUR RESEARCH

These PEEK adapters connect standard LC fittings to standard LC ports, usable with most common organic and inorganic HPLC solvents without risking corrosion, metal contamination, or protein degradation.

Supplier: VICI JOUR RESEARCH

Fiberglass reinforced PP with PP washers. A number of chromatography systems still require or prefer flanged connections. When the tubing is flanged, the washer never comes in contact with the mobile phase.

Supplier: OPTIMIZE TECHNOLOGIES

The EXP® Fitting System is the premier adjustable nut and ferrule compression fitting for extreme high-pressure connections between ¹/₁₆" tubing and any 10 to 32 port.

Supplier: OMNIFIT

Flanged tubing system is used for economical low pressure connection. A flanging washer is placed between the flange and the fitting nut. When screwed into a flat-bottom, the flange is compressesed against the bottom of the port to produce a seal.

Supplier: UPCHURCH SCIENTIFIC

PP or ETFE. Use these barbed adapters to connect peristaltic-type flexible tubing for general, low pressure applications, such as plumbing Ismatec® peristaltic pumps. Due to the low melting point of PP, these adapters are not autoclavable, however, they can be sterilised via gamma radiation. The ETFE connectors have superiour solvent resistance and a higher temperature rating (80 °C).

Supplier: UPCHURCH SCIENTIFIC

Ultra high performance fittings are manufactured from a proprietary PEEK blend (PK) which allow them to be used at higher temperatures (up to 200 °C) and higher pressures.

Supplier: VICI JOUR RESEARCH

PEEK one-piece fingertight fittings. 10-32 threads, for 1/16" tubing. Fingertight up to 350 bar (5000 psi).

Supplier: UPCHURCH SCIENTIFIC

VHP Microferrules are made from a proprietary high performance PEEK polymer blend, a material which is unique in its ability to enable the use of capillary tubing in UHPLC environments.

Supplier: UPCHURCH SCIENTIFIC

These adapters are made from PEEK or PTFE. Female to male 10-32 to 1/4-28 adapters.

Supplier: OMNIFIT

Omnifit® threaded adaptors are a useful range of problem solving parts that enable to convert thread sizes quickly and easily, accepting a ¹/₄"-28 UNF male fitting at one end and a range of male and female thread types at the other.