Accessories for glove boxes, Precise™

Automatic pressure controller for 230 V units, incl. mounting bracket, hardware, 3/16" ID polyvinyl tubing, 3/32" ID polyvinyl tubing, and power cord, for automatic control of the main chamber pressure, main chamber purging and filling cycles, and transfer chamber evacuation and filling cycles

Manual valve gas and vacuum tubing connection kit, with flexible vinyl tubing and fittings necessary to connect user-supplied inert gas supply tank and rotary vane vacuum pump to valves located on the glove box

Gas and vacuum tubing connection kit, automatic pressure controller, with flexible vinyl tubing and fittings necessary to connect user-supplied inert gas supply tank and rotary vane vacuum pump to valves located on the glove box

Add-A-Valve kit, incl. manual ball valve, compression fitting, hose connector fitting, O-ring and nut to add a service valve to the main chamber or transfer chamber; requires installation and Ø 0,688" hole

HEPA-filtered pressure relief vent kit, with 99,99% efficient HEPA filter; for ducting to the outside or room; may be used with 5241200 carbon-filtered vent kit

Carbon-filtered pressure relief vent kit, incl. activated carbon filter, for ducting to outside or room; may be used with 5238500 HEPA-filtered pressure relief vent kit

Pressure relief valve vent kit for exhaustig the pressure relief valve during overpressurization, incl. 3,9" OD × 3,8" ID thimble connection, gasket, two elbows, four clamps and 13" long tubing (Ductwork for outside venting and 5230600 Pressure Relief Valve are required but not included)

Moisture monitor/hygrometer for placement inside the main chamber to continuously monitor moisture levels and absolute moisture content in gas (0 - 10000 ppm); consists of chemically inert ceramic technology moisture sensor, sampling block, digital display monitor, sampling pump, switching power supply and on/off switch, for 230 V units

Digital hygrometer, handheld, measures both percent relative humidity from 0-100% and temperature in ° F/° C; incl. 9 volt alkaline battery

Oxygen monitor, dor detecting trace oxygen levels using an electrochemical sensor; digital readout in three measurement ranges of 0-100 ppm, 100-1000 ppm and 1000-10000 ppm, for 230 V units

Oxygen monitor for 115/230 V, measures percent of oxygen (0,1 - 100 %) inside the glove box using a chemically resistant electrochemical sensor, incl. interconnecting sensor cable and power cord for connection to the glove box’s interior electrical receptacle

Exterior oxygen monitor tubing kit (For use with Oxygen Monitor 5244500 and 5244501)

Exterior oxygen monitor tubing kit (For use with Moisture Monitor 5244900 + 5244901)

Oxygen and moisture removal column, for reduceing the oxygen level to less than 5 ppm and moisture level to less than 50 ppm; requires connection to two manual valves on the main chamber and a diaphragm vacuum pump for atmosphere oxygen/moisture removal and recirculation

Support stand for oxygen and moisture removal column

Oxygen and moisture removal tubing kit, incl. 25' fluorinated ethylene propylene (FEP) tubing, eight tube inserts and two connectors to connect the Oxygen and Moisture Removal Column to diaphragm pump

Canister with stand for holding any trap insert, clear polypropylene canister allows visual inspection of trap contents

Drying train tubing kit, incl. 25' fluorinated ethylene propylene (FEP) tubing and eight tube inserts to connect drying train components

Flowmeter, for inline drying train connection to provide visual confirmation of drying train circulation

Gas and vacuum 0,2 µm filter, traps particulates; for drying train or vacuum pump exhaust; 0,25" - 0,38" ID

Diaphragm pump for drying train circulation, for 230 V units, 35 l/minute displacement capacity

Drying train, with 1 molecular sieve column, 220 V, 50/60 Hz

Drying train, with 2 molecular sieve columns, 220 V, 50/60 Hz

Optional second column for drying train

Molecular sieve replacement media, for drying trains

Flat work surface, black epoxy resin, may be placed atop two Protector Standard Base Cabinets to support Precise™ glove boxes, 1524×762×31,75 mm

Electrical pass-through kit, provides a leak-tight connection for data transfer to a printer or computer; incl. sealed 9 pin connector (D-subminiature with male pins on one side and female pins on the other) and 10' cord; requires installation and drill hole; Installation Kit 5241100 is recommended

Electrical power strip, UK-plug, 250 volts, 2 amps, 6 receptacles

Ionizer fan, anti-static, for 230 V units, 50/60 Hz operation

Viewing window, acrylic (749×396×12,7 mm) with dry powder epoxy-coated steel frame, replaces standard laminated glass window

Electrical 9-Pin Pass-Through installation kit, incl. drill bits and holesaws for installing 5075619 Electrical 9 Pin Sealed Pass-Through

Electrical power strip, EU-plug, 250 volts, 2 amps, 4 receptacles

Bottle holder, epoxy-coated steel, with 3" diameter opening, holds a squirt bottle or other round container

Tissue holder, epoxy-coated steel, accommodates a box of tissues in the upside down or upright position; opening in the holder permits wipes to be dispensed from the bottom

Rear shelf kit, incl. four stainless steel shelves and epoxy-coated steel vertical uprights, with stainless steel slotted back for mounting Hanging Shelf Kits (sold separately); assembled dimensions: 563,88×508×111,76 mm

Left side shelf kit, incl. four stainless steel shelves and epoxy-coated steel vertical uprights, for storage in left side of the main chamber to maximise space; assembled dimensions: 538,48×508×111,76 mm

IV bar kit for supporting intravenous solution bottles and bags, incl. 21.2" long stainless steel bar, mounting hardware and four snap hooks; requires Shelf Kit 5235000 or 5235001 (not included)

Exterior transfer chamber shelf, dry powder epoxy-coated steel shelf, 271,78×383,54, for mounting to top of transfer chamber to maximise exterior work area

Hanging organizer bin (137,16 mm), plastic, container holds miscellaneous small items

Hanging organizer bin (187,96 mm), plastic, container holds miscellaneous small items