You searched for: Chromatography Supplies

Supplier: Agilent

A range of high quality supplies and components for the Integrated Sample Introduction System (ISIS) for use with the 7700 ICP-MS range.

Supplier: Agilent

Key design features of nebulisers for PerkinElmer ICP-MS systems provide the best precision, efficient drainage, minimal burner blockage, and reduced interferences.

Supplier: Agilent

Replacement RRLC nebuliser for G4218A ELS detector

Supplier: Agilent

These torches are suitable for PerkinElmer ICP-MS systems.

Supplier: Agilent

Before ordering parts for FID maintenance, determine which type of FID is installed on your GC. The FID is available in two versions: Dedicated, capillary optimized: for capillary columns only. Adaptable: for packed or capillary columns.

Supplier: Agilent

The Programmable Sample Dispensers (PSD) are high-capacity autosamplers that are used with Graphite Furnace AA.

Supplier: Agilent

In 2005, Agilent released an improved FPD with minimum detectable levels (MDL) of 3,6 pg/s for sulphur and 60 fg/s for phosphorus. This is more than a five times improvement for sulphur.

Supplier: Agilent

These nebulisers for PerkinElmer AA systems provide the best precision, efficient drainage, minimal burner blockage, and reduced interferences.

Supplier: Agilent

Mark 7 Spray Chambers for flame atomisation System. Easy-to-use twist and lock assembly allows for easy cleaning and routine maintenance.

Supplier: Agilent

Nitrogen Chemiluminescence Detector (NCD) is a nitrogen-specific detector that produces a linear and equimolar response to nitrogen compounds based on a chemiluminescent reaction of NO with ozone.

Supplier: Agilent

CrossLab piston seal, reversed-phase, For: Thermo UltiMate 3000 RS and SD pump series

Supplier: Agilent

Inert kit for ICP-MS enables analysis of high-purity and HF-containing samples using a PFA-based sample intro system with inert Pt or sapphire-injector torch.

Supplier: Restek

Sapphire piston

Supplier: Restek

Isolation seal, For: 7010

Supplier: VARIAN

Tube collector

Supplier: VARIAN

Sparge probe replacement kit, for S/N below 995, hexagonal base

Supplier: Restek

O-rings for Agilent trap fittings

Supplier: Restek

In-line filter, 7 µm, Siltek treated

Supplier: VARIAN

Difflok cap, silcosteel, markes unity

Supplier: Merck

Merck columns come in three formats.

Supplier: Merck

FocusLiner™ inlet liners are designed with wool plug to promote the rapid vaporisation of the entire sample, minimise mass discrimination, and prevent non-volatile material from entering the column. It incorporates a unique design to prevent the shifting of the wool plug during repeated injections or sudden inlet pressure changes. These liners are suitable for Agilent, Perkinelmer, Shimadzu, Finnigan, Varian and Thermo scientific equipped with split/splitless inlets.

Supplier: Merck

SPME-GC inlet liners are designed for optimum sample introduction for specific injection techniques that are suitable for Agilent, Perkinelmer, Shimadzu, Finnigan, Varian and Thermo scientific equipped with split/splitless inlets.

Supplier: VWR Collection

ChromasterUltra Rs, ChromasterUltra Rs plunger for 6170 binary pump

Supplier: Merck

These SPME fiber assemblies can be reused for up to 100 analyses depending on the application.

Supplier: VWR Collection

Chromaster, Chromaster Plus HPLC interface control board for Chromaster Plus system control. USB cable and e-line cable (0,5 m) included, built into the autosampler upon installation in laboratory, if no autosampler is used, then the interface box (S) must be ordered instead

Supplier: Avantor

J.T.Baker®, Adapter, blue, for attaching reservoir or Luer tip to PP SPE columns

Supplier: VWR Collection

This spare part is suitable for Chromaster 5210 and 5260 autosamplers. For Chromaster 5210 AS from Serial No. 1309-001 and 1309T-001 onward. For Chromaster 5260 AS from Serial No. 1205-001 and 1205T-001 onward.

Supplier: VWR Collection

Primaide™, Primaide™ HPLC UI control keypad, For: Primaide™ PM1210 autosamplers

Supplier: VWR Collection

Maintenance parts kit for Chromaster HPLC 5110 pumps. Kit contains 2× pump seal 655-1080, 4× packing (A) 810-1345, 1× packing 638-1422, 1× filter 638-1423, 1× packing 638-1424, 2× wash seal 885-1884, 1× drain valve seal 885-2920, 1× packing 885-1505, 2× packing (B) 891-1364

Supplier: VWR Collection

Tubing for 3-column selector, ID 0,25, OD 0,79 - 200 mm