You searched for: PE/LDPE/HDPE Stoppers

Supplier: VWR Collection

Stopper for test tubes Ø 12 to 16 mm, polyethylene, with tongues.

Supplier: VWR Collection

Drain stoppers, VWR®

Supplier: VWR Collection

Greaseless closure, which prevents ground joints from seizing. With inclined, circumferential sealing lips for better sealing and reduced risk of breakage. Easily detachable. With ergonomically shaped grip.

Supplier: Simport Scientific

Ideal closures for glass and plastic reagent, sample and culture tubes, LDPE.

Supplier: HELLMA

An assortment of stoppers for use with standard Hellma® cells.

Supplier: Simport Scientific

HDPE. Fit tubes of 15 ml capacity and 17 mm Ø.

Supplier: GRANT INSTRUMENTS

Drain stoppers, recommended when using heat transfer beads, to prevent beads entering the drain hole.

Supplier: B. Braun

These PE Combi-Stoppers are used for sealing male or female Luer-Lock and Luer-Slip connections.

Supplier: B. Braun

IN-Stopper is a male luer lock closing cone with injection port for intermittent injections through injection membrane. It closes female accesses and offers a needle access via an injection membrane, e.g. to an infusion solution and has got a smooth, hygienic outer surface.

Supplier: Bohlender

For closing ground joint parts. With ground joint and sealing rings on the outside; knurled or hexagonal grip. Compared with glass stoppers, they are easily removable and can be used without grease.

Supplier: Simport Scientific

PE Plug type push-in caps and 2-position snap caps are made of polyethylene for test tubes with outside diameters of 12 or 17 mm. Dual position caps offer two possibilities: the closed but unsealed position where samples are maintained aerobic for microbiological procedures; and the fully sealed position where the cap is pushed tight to seal the tube for anaerobic use or for storage, transfer and centrifuge applications.

Supplier: Simport Scientific

Designed for easy-on, easy-off use. Cap removal is simple and quick. FitsAll™ closure is ideal for recapping most 12 and 16 mm O.D. evacuated glass blood collection tubes. Flexible FitsAll™ closures protect from aerosols of highly infectious microorganisms. They guard samples against cross-contamination and laboratory work areas against infection and spillage. Precision molded from low-density polyethylene, FitsAll™ fits firmly on the tube. Not suitable for autoclaving.

Supplier: KARTELL

Stoppers for disposible tubes, PE.

Supplier: SciLabware

These PE stoppers are ideally suited for use with glass or plastic volumetric flasks and measuring cylinders etc. which have longer 'B' length sockets.

Supplier: Brand

PP or PE-LD, hollow, with sealing ribs and square or octagonal grip.

Supplier: COWIE

PTFE. Stopper with flat head fit standard ground glass joints.

Supplier: KARTELL

Finned plugs for disposable tubes 11 to 13 mm or 15 to 17 mm in diameter. The finned plug has been carefully designed. Available colours: Neutral (00), blue (04), red (10), green (12) and yellow (06).

Supplier: COWIE

Fit standard ground glass joints.

Supplier: DWK Life Sciences

HDPE, linear, ideal for flasks that are grounded to [ST] stopper dimensions.

Supplier: GLASWARENFABRIK KARL HECHT

High-density polyethylene.

Supplier: KARTELL

Stoppers with coloured insert in the holding disc for better identification.

Supplier: VITLAB

Stopper for Standard Ground Joints, PP, hexagonal-knob cap, NS: 34/35, White/red

Supplier: KARTELL

For sealing glass or plastic reagent and sample tubes.

Supplier: DWK Life Sciences

Octagonal PE stoppers.

Supplier: KARTELL

Tapered stoppers, PTFE, plastilab®, NS: 14/23, Ø bottom: 12,2 mm

Supplier: KARTELL

PP, transparent, with 2 hose attachments, 8 mm Ø. Ideal for ventilating or transferring air, gases or liquids in a container with a normal ground joint sleeve.

Supplier: RATIOLAB

PE.

Supplier: MACHEREY-NAGEL

PE plugs with a diaphragm for safe penetration of the needle are used for the shell vials.

Supplier: Corning

Coloured stoppers from LDPE.

Supplier: Corning

Material LDPE.