You searched for: Chromatography Supplies

Supplier: Restek

This heater cartridge and PRT sensor can be used with 5890 FID and split/splitless weldments.

Supplier: Restek

Replacement parts for Shimadzu HPLC systems.

Supplier: Restek

This kit is used exclusively with Agilent 5890 GCs.

Supplier: Restek

This split/splitless injection port changes inlet liners faster and more easily.

Supplier: Restek

Caps features a smooth inner surfaces for easier cleaning. Suitable for for ASE systems.

Supplier: Restek

Use these liners for increased sensitivity.

Supplier: Restek

Inlet liners with deactivation improve trace-level analysis that are suitable for agilent GCs equipped with split/splitless inlets. It is made of borosilicate glass.

Supplier: Restek

Trident direct system can be used to select the right level of protection for analysis. It provides the protection against particulate matter and moderate protection against irreversibly adsorbed compounds.

Supplier: Restek

These FID capillary column adapters made of stainless steel are ideal for PerkinElmer Auto SYS XL.

Supplier: Restek

Liners are used for conversion of ¼" packed injection port.

Supplier: Restek

Installation kit for 1 mm ID columns; for valve applications, Kit contains 1× Valco nut 1,58 mm, 1× stainless steel nut 1,58 mm, 1× Vespel/graphite ferrule 1,58 mm, 1× graphite ferrule 1,58 mm, 1× stainless steel ferrule, 1× stainless steel front ferrule 1,58 mm, 1× stainless steel back ferrule

Supplier: Restek

Carriage motor belt for Agilent 7673A, 7673B and 7673C autosamplers.

Supplier: Restek

Set the column flow rate by injection the methane and optimising linear velocity is preferred method for establishing reproducible retention times.

Supplier: Restek

This kit contains the tubing and fittings needed to add an additional GC to lab bench.

Supplier: Restek

Frit adaptors

Supplier: Restek

These capillary dedicated FID replacement jet for Agilent 5890/6850/6890/7890 GCs are available in standard, high-temperature or Siltek treated high-performance versions.

Supplier: VARIAN

Load and Lock 4003 column, spare parts kit

Supplier: Restek

Z-Belt for use with Agilent 7673B and 7683 autosamplers.

Supplier: Restek

These direct injection glass inserts are suitable for 6,35 mm packed column injection ports.

Supplier: Restek

FID/NPD capillary adapter fitting, high-quality stainless steel, for Agilent 5890/6850/6890 GC's

Supplier: Restek

Flow splitters with fluid resistor technology eliminate the adjustments to the capillary tubing for optimising split ratio with wide range of interchangeable resistors.

Supplier: Restek

Injector mounting post for Agilent 7673 series autosamplers, for use with 6890 GCs

Supplier: Restek

This easy to use adapter fitting is sturdy and made of compact stainless steel.

Supplier: Restek

Autosampler plunger carrier belt for Agilent 7673A and 7673B autosamplers.

Supplier: Restek

A complete column packing system which is used to pack the analytical HPLC columns.

Supplier: Restek

Tube made of stainless steel are durable and unconditioned.

Supplier: DOMNICK HUNTER

Maintenance kit 4000 hours for all LC-MS

Supplier: VARIAN

Solid phase microextraction (SPME) is a technique for extracting analytes from solid, liquid or gaseous samples by adsorbing them onto the SPME fiber and then desorbing them into an inlet, either on a gas chromatograph (GC) or an HPLC system. SPME is amenable to automation using an autosampler or it can be performed manually as well.

Supplier: AGILENT HEWLETT PACKARD

The micro ECD has a detection zone volume 10 times smaller than any other ECD with replicable inlet liner to decreasing column contamination of the cell.

Supplier: Thermo Fisher Scientific

Sample loop, for 9010, 9725 and 9725i injectors, PEEK, 20 µl, For tube I-Ø: 0,25 mm