You searched for: Valves

Supplier: Bohlender

Body made of PTFE with two connections with female thread UNF 1/4" 28 G. Valve made of PPS with set screw and lock nut for adjusting and fixing pressure between 0,1 and 5 bar.

Supplier: Avantor Fluid Handling

Specifically designed for Masterflex® pump tubing.

Supplier: Avantor Fluid Handling

Resist pressures up to 500 psi!

Supplier: Avantor Fluid Handling

Particles will not cause damage.

Supplier: Avantor Fluid Handling

Provides security and safety where most needed.

Supplier: ENTEGRIS

Available compliant to SEMI Standard F57-0312, the specification for polymer components used in ultrapure water and liquid chemical distribution systems. Higher performance with greater back (outlet) pressure capability. All wetted parts are molded PFA providing chemical resistance suitable for use in high purity, high corrosive chemical handling applications.

Supplier: Avantor Fluid Handling

Offer outstanding potential for precision control in liquid and gas analysis.

Supplier: Avantor Fluid Handling

Easily meter corrosive fluids or gases.

Supplier: Bohlender

Two-way valve with straight bore and two connections with GL thread completely made of PTFE.

Supplier: VACUUBRAND

VM series valves are hand operated diaphragm valves. They are used as isolation valves, air-admittance valves or manual-control valves.

Supplier: HAMILTON BONADUZ

This MTB sampling valve is a lever-actuated on/off valve used for storing and transporting samples in any Gastight® PTFE Luer lock (TLL) or Luer tip (LT) syringe.

Supplier: Welch by Gardner Denver

These manually operated butterfly valves are made of stainless steel with viton seal.

Supplier: ENTEGRIS

Available compliant to SEMI Standard F57-0312, the specification for polymer components used in ultrapure water and liquid chemical distribution systems. Three and one-half complete turns fully opens or closes the valve for more precise control than a ¹/₄-turn valve. Slower actuation reduces water hammer affect on fluid stream. All wetted parts are molded PFA providing chemical resistance suitable for use in high purity, high corrosion chemical handling applications.

Supplier: Welch by Gardner Denver

These high vacuum through valves feature a very long life bellows-seal made from stainless steel.

Supplier: ENTEGRIS

This 3-way valve (patent-pending) has an all-PFA valve body and high purity fluoropolymer wetted components providing a noncontaminating fluid stream and chemically compatible construction. Compliant to SEMI Standard F57-0301, the specification for polymer components used in ultrapure water and liquid chemical distribution systems.

Supplier: HAMILTON BONADUZ

HV plug valves provide an economical and flexible method of custom-building a fluid flow control system, from a simple on/off valve to a more complex multi-valve arrangement, using a combination of loop and distribution valves.

Supplier: Welch by Gardner Denver

These high vacuum angle valves feature a very long life bellows-seal made from stainless steel.

Supplier: VACUUBRAND

The VS, VS C and VS B series valves are butterfly-type valves which offers very good conductance. The VS C series features a valve seal made of perfluorelastomer material (FFKM).

Supplier: ENTEGRIS

Available compliant to SEMI Standard F57-0312, the specification for polymer components used in ultrapure water and liquid chemical distribution systems. All PFA valve body and high purity fluoropolymer wetted components for use in high purity, highly corrosive chemical handling applications.

Supplier: VACUUBRAND

Gas inlet valves are small hand operated valves for admitting gases into a vacuum system.

Supplier: Avantor Fluid Handling

Easily control your outlet pressure.

Supplier: ENTEGRIS

Available compliant to SEMI Standard F57-0312, the specification for polymer components used in ultrapure water and liquid chemical distribution systems. All wetted parts are molded PFA providing chemical resistance suitable for use in high purity, high corrosive chemical handling applications.

Supplier: VACUUBRAND

These straight-through valves with electromagnetic (solenoid) drive are used for operating cycles with short intervals and it is often used as vacuum control valves. The straightforward design provides a valve with low leakage rate.

Supplier: ENTEGRIS

This 3-way valve (patent-pending) has an all-PFA valve body and high purity fluoropolymer wetted components providing a noncontaminating fluid stream and chemically compatible construction. Compliant to SEMI Standard F57-0301, the specification for polymer components used in ultrapure water and liquid chemical distribution systems.

Supplier: ENTEGRIS

Available compliant to SEMI Standard F57-0312, the specification for polymer components used in ultrapure water and liquid chemical distribution systems. Three-ported directional valve enables simplification of piping system design while minimising its footprint. All PFA wetted surfaces for ultrapure and corrosion resistant performance.

Supplier: ENTEGRIS

O-ring free design, ¹/₂ or ¹/₄" orifice.

Supplier: VACUUBRAND

Valves of the VK series are sturdy isolation devices for the rough and fine vacuum range. The VKE series uses stainless steel for the metal parts and fiberglass reinforced PTFE seatings.

Supplier: IDEX RHEODYNE

Combine MX Series II™ modular valves with an instrument currently in use to support complex fluid switching and sample injection needs.

Supplier: VACUUBRAND

These valves are compact air admittance valves with small flange. The VB valve is manually operated. On rotating the knurled screw cap the valve disc is lifted off the seating and air enters through the holes. The valve disc is rotatable. Therefore the valve seat seal is prevented against wear during opening and closing.

Supplier: Welch by Gardner Denver

Small flange valve, open type, made of nickel-plated aluminium.