You searched for: Distillation Components

Supplier: Chemglass

Claisen-style adapters with an additional standard taper outer joint at a 45° angle to the vertical outer joint.

Supplier: Chemglass

Distillation receivers feature an overflow tube.

Supplier: Chemglass

Compact and simple distilling adapter for use with process reactors. Vapor flows upward freely and distillate is collected in to the small bowl below the joint and through the stopcock into a distilling receiver.

Supplier: Corning

Receivers, made of PYREX® brosilicate glass, are designed for determining water by distillation.

Supplier: Chemglass

Cow type design has three receivers 45° apart.

Supplier: Kemtech America

Used in distillation of very small amount of distillate at lower temperature with high efficiency

Supplier: Kemtech America

With Vigreux indentations.

Supplier: Kemtech America

Condenser is a combination of a cold coil and Liebig.

Supplier: United Scientific Supplies

Quick setup for distillation

Supplier: Kemtech America

Joint on side tube accommodates 25 mm immersion thermometer.

Supplier: Chemglass

Designed to maintain distilled solvents in an inert atmosphere.

Supplier: Chemglass

Radial style distillation receiver allows four flasks to be progressively filled.

Supplier: G.S.C. INTERNATIONAL, INC.

No two liquids have exactly the same boiling point. Therefore it is possible to separate any mixture of two liquids by raising the temperature of the mixture to a point where one of the liquids will boil but the other will remain liquid.

Supplier: DWK Life Sciences (KIMBLE)

Column features a [ST] 14/10 joint and indentations over the entire length to optimize vapor-liquid contact.

Supplier: Chemglass

Distillation kit for 10 and 20 L reactor systems

Supplier: CHEM SCIENCE INC CA

These solvent still high vacuum valves have PTFE covers on the shaft and tip.

Supplier: Wards

High quality Vigreux column used to separate vaporized mixtures of liquid compounds with close volatility.

Supplier: DWK Life Sciences (KIMBLE)

These columns are plain fractionating column with indents to support packing.

Supplier: Corning

These PYREX® 60° angle distilling connecting adapters have a 24/40 Standard Taper outer joint at the upper end and inner 24/40 Standard Taper joints and on the sidearm and lower joints

Supplier: Chemglass

With [ST] joints on both top arms and on lower inner joint

Supplier: Chemglass

Adapters have a #7 Chem-Thread at the top for a vacuum-tight seal of plain stem thermometers.

Supplier: Chemglass

Simple distillation head with a condenser sealed to the adapter at a 75° angle.

Supplier: Chemglass

Adapter is placed above flask to prevent carry-over of reactions which have a tendency to foam.

Supplier: Kemtech America

Centrifuge tube shaped receiver with an upper standard taper joint.

Supplier: Kemtech America

With the Vigreux column vacuum jacketed to improve distillation performance.

Supplier: Corning

Distallation receiver to determine the amount of dilution in crankcase oils when gasoline has been used as fuel. Receiver design keeps heat-sensitive materials away from the hot base of the flask. Receiver has a [ST] 24/40 top outer joint and a [ST] 24/40 sidearm inner joint.

Supplier: Wards

This simple distillation apparatus is made up of boroscilicate glass.

Supplier: Corning

Cyanide distilling apparatus made of PYREX® borosilicate glass to determine soluble and insoluble cyanides in water.

Supplier: General Glass Blowing

The Self Evacuating Cash Still complies with the AOAC method to determine Acidity (Total Volatile) of wines. The steam chamber is heated by an 800 watt immersion coil that heats the distilled water to a boiling point in about 3 to 4 minutes.

Supplier: Chemglass

Similar in design to the AF-0720 solvent distillation apparatus, but without a delivery adapter.