You searched for: Tube Racks

Supplier: Bel-Art Products, a Part of SP

Excellent space-savers for use in water baths, laminar flow hoods, fume hoods or any place where space is limited.

Supplier: Bel-Art Products, a Part of SP

These heavy-duty 3 tier racks are stackable and compact, and have hand grips in the end plates for easy transport.

Supplier: Bel-Art Products, a Part of SP

Chemical- and corrosion-resistant steel wire test tube racks are coated with heat-cured epoxy for long life and easy cleaning.

Supplier: Bel-Art Products, a Part of SP

High-quality epoxy-coated wire racks in convenient extra-long sizes for volume test tube work.

Supplier: AGILENT TECHNOLOGIES, INC (CSD) CA

Sample racks & overlays for SPS 4, SPS 3 & ASX 500 autosamplers for AAS, ICP-OES, MP-AES & ICP-MS.

Supplier: Bel-Art Products, a Part of SP

Rack emulates the 96-place format used in microplates, deep well plates, and other tools configured for drug research and robotic applications.

Supplier: Bel-Art Products, a Part of SP

Unique tabs protect your samples from loss and contamination.

Supplier: Thermo Fisher Scientific

For incubation at elevated or reduced temperatures in water or ice baths.

Supplier: Bel-Art Products, a Part of SP

This all-polypropylene rack provides efficient and extended cooling of twenty-eight 50 mL centrifuge tubes in a chilled bath.

Supplier: Thermo Fisher Scientific

Racks are ideal for use below 4°C (39.2°F)

Supplier: Bel-Art Products, a Part of SP

Specifically designed for incubating 1.5 mL microcentrifuge tubes, this rack includes a hold-down disk to maintain a constant pressure on the tube caps and prevent them from opening during internal air expansion.

Supplier: Bel-Art Products, a Part of SP

The No-Wire™ racks fit neatly into round containers such as ice buckets and beakers, as well as desiccators.

Supplier: Bel-Art Products, a Part of SP

Double-sided, compact polypropylene plastic racks are perfect for use on the benchtop or in the freezer.

Supplier: Bel-Art Products, a Part of SP

Molded of steam autoclavable polypropylene, these racks fit 400 mL or 1000 mL beakers.

Supplier: Thermo Fisher Scientific

These polypropylene racks are molded in one piece and have a three-tier, grid design

Supplier: Bel-Art Products, a Part of SP

This holder solves the problem of where to put a single 50 mL conical tube where it will not roll or spill.

Supplier: Corning

Microtube racks are available in three sizes and are designed to accommodate microtubes or screw-cap microtubes.
The 48-place aluminium rack holds 48 screw-cap tubes of all sizes. Unique ribbed-port design allows one-hand operation, supported by non-skid benchtop pads for a firm platform. Long-lasting aluminium construction. Centre support for added strength and stability.

Supplier: Bel-Art Products, a Part of SP

Molded from a special blend of polypropylene that is heavier than water, these racks sink to the bottom of the bath and will not tip over.

Supplier: Bel-Art Products, a Part of SP

Leave hands free for pipetting and other critical tasks with these polystyrene plastic tube holders that securely hold a 50 mL conical centrifuge tube.

Supplier: Bel-Art Products, a Part of SP

Incubate up to 24 microcentrifuge tubes in a water bath (choose from 1.5 mL or 0.5 mL size).

Supplier: Bel-Art Products, a Part of SP

Round holes with tight tolerances hold 13 mm tubes firmly for accurate processing, thus reducing lost samples and potential damage to instruments. Increased efficiency is achieved by using the numbered locations for programming, resulting in higher throughput.

Supplier: Bel-Art Products, a Part of SP

The most versatile tube holder on the market, this set-up takes just seconds and gives users the choice of creating a 15 mL or a 50 mL tube holder.

Supplier: Bel-Art Products, a Part of SP

This 20 place polypropylene round floating rack fits most cryotubes and holds them tightly in a circular pattern formed by 12 outer and 8 inner openings.

Supplier: Bel-Art Products, a Part of SP

Attachment securely holds 1.5 mL microcentrifuge tubes in an 8 or 20 capacity disk for simultaneous vortexing.

Supplier: Beckman Coulter

Molded plastic racks support tubes in Aerosolve® canisters.

Supplier: Brandtech

Polished Type 304 stainless steel racks reduce porosity and provide excellent corrosion resistance in harsh atmospheres.

Supplier: Eppendorf

Made from stainless-steel with inserts to help retain tubes and prevent them from spinning in the rack.

Supplier: Brandtech

Sturdy polypropylene racks snap together for easy assembly.

Supplier: Labconco

Hold tubes in upright position within a flask for freeze drying.

Supplier: Heathrow Scientific

OneRack® Tube Racks are tough and highly resistant to acids, bases, solvents, and heat.