You searched for: Graticules, Reticles and Grids

Supplier: ELECTRON MICROSCOPY SCIENCE

Suspended germanium provides a unique calibration standard for x-ray energy dispersive spectroscopy. Since Ge is not typically found in TEM columns, the calibration samples provide a material that cannot be mistaken for instrument components and their signal peaks. The regime in which system peaks normally occur (2 to 9 keV and 11 to 20 keV) is devoid of peaks from the Ge.

Supplier: Electron Microscopy Sciences

The formvar coated grids are stabilized with an evaporated carbon film. This type of coating is excellent for specimen support, especially for ultra thin sections. All film is laid on the shiny side of the grid.

Supplier: ELECTRON MICROSCOPY SCIENCE

CVD Graphene TEM support films are supported by lacey carbon film on a 300 mesh copper TEM grid. The graphene film appears as a near-transparent to light-grey film on the surface of the Lacey Carbon mesh on a red-brown colored copper TEM grid.

Supplier: Electron Microscopy Sciences

QUANTIFOIL® is a carbon film for electron microscopy or low-energy electron point source microscopy.

Supplier: Electron Microscopy Sciences

Reticle A is designed for general laboratory use (5 mm long, with 0.1 mm divisions) and reticle B (⁴/₁₆ " long, ¹/₆₄" divisions) is most frequently used in textiles or electronics, and where measurement in mils is required. Reticle C (5000 µm long, with 50 µm divisions) is calibrated in microns and helpful for pesticide droplet size measurements or anywhere measurements in microns are required.

Supplier: Electron Microscopy Sciences

Parallel and crossed line grating replicas are calibration specimens for transmission electron microscopy and scanning transmission electron microscopy.

Supplier: Electron Microscopy Sciences

Gauge pairs occupying a field of view of 10 mm. Each gauge is proportional to its adjacent number. The approximate size of the smallest pair is 0.1 mm.

Supplier: Electron Microscopy Sciences

The specimen is racked on the mechanical stage of the microscope and traverses are taken right across thee deposit sizing all the particles encountered.

Supplier: Electron Microscopy Sciences

QUANTIFOIL® is a carbon film for electron microscopy or low-energy electron point source microscopy.

Supplier: Electron Microscopy Sciences

Custom 4-post lift-out grids for in-situ lift-out. It include multiple indexed mounting locations, two with vertical bars attachment surfaces and two with 'V' shaped alignment surfaces.

Supplier: Electron Microscopy Sciences

Alphabetical and numerical systems for recording specimen locations on the grid.

Supplier: Electron Microscopy Sciences

The 3 post copper lift-out grids are specifically designed for in-situ lift-out. These grids include multiple indexed mounting locations with both vertical bar and 'V' shaped attachment surfaces. These grids have a shallower downset and slightly wider center post.

Supplier: Electron Microscopy Sciences

Gilder grids are a reliable support specimen grid for transmission electron microscopy.

Supplier: Electron Microscopy Sciences

EMBRA electroformed grids combine a high open area with a rigid construction which allows for relatively easy handling. Measures 3.05 mm in diameter and 16 micron in thickness. Material: Copper (Cu), Nickel (Ni), Gold (Au), Stainless Steel (SS), Titanium (Ti), Molybdenum (Mo), Aluminum (Al).

Supplier: Electron Microscopy Sciences

The microscope graticle is used for measurements in two directions for sighting and alignment.

Supplier: Electron Microscopy Sciences

For calibrated measurement in a light microscope.

Supplier: Electron Microscopy Sciences

Stage graticules are used for the routine calibration of eyepiece patterns, particularly when alternating between objectives on one microscope or when using the same graticule in different microscopes.

Supplier: Electron Microscopy Sciences

High Grade Maxtaform grids with clean and smooth edges, firm support, and a large open area.

Supplier: Electron Microscopy Sciences

QUANTIFOIL® is a carbon film for electron microscopy or low-energy electron point source microscopy.

Supplier: Electron Microscopy Sciences

A thin film of pure formvar resin coats the shiny side of a Thin Bar Square grid. Coated grids are optically checked and batch tested in the electron microscope.

Supplier: Electron Microscopy Sciences

C-flat™ is an ultra-flat, holey carbon-coated TEM support grid for transmission electron microscopy (TEM).

Supplier: Electron Microscopy Sciences

QUANTIFOIL® is a carbon film for electron microscopy or low-energy electron point source microscopy.

Supplier: Electron Microscopy Sciences

The formvar coated grids are stabilized with an evaporated carbon film. This type of coating is excellent for specimen support, especially for ultra thin sections. All film is laid on the shiny side of the grid.

Supplier: Electron Microscopy Sciences

Graphene is a single atomic layer of carbon atoms tightly packed in a two-dimensional honeycomb lattice, ideal TEM support film.

Supplier: Electron Microscopy Sciences

EMS square mesh and oval hole grids are a reliable support specimen grid for transmission electron microscopy.

Supplier: Electron Microscopy Sciences

Use as crossed lines, but for the measuring of distances between thelines. Greater accuracy can be obtained by locatng the specimen detail between the graticules gauge pair.

Supplier: Electron Microscopy Sciences

QUANTIFOIL® is a carbon film for electron microscopy or low-energy electron point source microscopy.

Supplier: Electron Microscopy Sciences

Simple counting for geological and soil analysis.
Reference: L.G. Briarty. “Stereology: Methods for Quantitative Light and Electron Microscopy.” Sci. Prog. Oxf. 1975 62; 1-32

Supplier: Electron Microscopy Sciences

EMS offers a series of calibration standards with one and two dimension calibrated patterns. The standards come in two grid spacings – 300 nanometers and 700 nanometers. These standards are created utilizing holographic interference of a particular laser frequency. They are typically accurate to < 1% across the entire surface of the standard.

Supplier: ELECTRON MICROSCOPY SCIENCE

The continuous ultrathin film on holey carbon film allows for the thinnest support film that still has adequate strength to withstand specimen preparation.