You searched for: Fittings and Connectors

Supplier: OMNIFIT

Omni-Lok™ inverted cone fittings provide a simple, easy to use low-pressure connection. Only the ETFE cone is in the fluid path.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® MicroTight®, F-124H, fitting, micro headless knurl, PEEK blue, 6-32 coned port, for 360 μm OD tubing, 5000 psi, PEEK

Supplier: UPCHURCH SCIENTIFIC

MarvelX biocompatible PEEK-lined stainless steel UHPLC connection system is easy to use and eliminates dead volume. It also provides higher repeat uses without sacrificing from consistent performance.

Supplier: UPCHURCH SCIENTIFIC

LuerTight™ fittings are designed for connecting fluoropolymer tubing without barbs or nuts. By integrating ferrules into the Luer bodies, these fitting reliably hold tubing in place while giving the convenience of a Luer connection.

Supplier: UPCHURCH SCIENTIFIC

PEEK, stainless steel or PCTFE.

Supplier: UPCHURCH SCIENTIFIC

PEEK.

Supplier: Restek

These internal cross are made of stainless steel. Used to connect four lines. Ideal for 1,6 mm OD tubing.

Supplier: Restek

Internal tees are made of stainless steel are used to connect three lines. Suitable for 1,6 mm OD tubing.

Supplier: UPCHURCH SCIENTIFIC

ETFE or PEEK.

Supplier: UPCHURCH SCIENTIFIC

PEEK polymer adapters connect peristaltic tubing to standard rigid or semi-rigid tubing.

Supplier: Bohlender

For connection of sensors with male thread PG to BOLA reactor lids.

Supplier: Restek

Internal uniona are made of 300 series stainless steel with end of tubing that seats squarely at bottoms of fitting details. Suitable for 1,6 mm OD tubing.

Supplier: UPCHURCH SCIENTIFIC

Ultra high performance fittings are manufactured from a proprietary PEEK blend (PK) which allow them to be used at higher temperatures (up to 200 °C) and higher pressures.

Supplier: UPCHURCH SCIENTIFIC

NanoPort™ assemblies provide consistent fluid connections for chip-based analyses, connections will bond to a variety of substrate materials with the use of Loctite™.

Supplier: Restek

Replacement long nut connects stainless steel tubing to a Rheodyne® 6-port valve or other Rheodyne® part.

Supplier: UPCHURCH SCIENTIFIC

PP or ETFE. Use these barbed adapters to connect peristaltic-type flexible tubing for general, low pressure applications, such as plumbing Ismatec® peristaltic pumps. Due to the low melting point of PP, these adapters are not autoclavable, however, they can be sterilised via gamma radiation. The ETFE connectors have superiour solvent resistance and a higher temperature rating (80 °C).

Supplier: VICI JOUR RESEARCH

These PEEK adapters connect standard LC fittings to standard LC ports, usable with most common organic and inorganic HPLC solvents without risking corrosion, metal contamination, or protein degradation.

Supplier: Restek

These ferrules are made of aluminium eliminate out-gassing and make leak-tight seals for less detector noise. Its unique two-piece design permanently locks on fused silica tubing without causing breakage.

Supplier: UPCHURCH SCIENTIFIC

PEEK or stainless steel.

Supplier: NRG DEVELOPMENTS

These adaptors used to convert the 2" BSP thread to fit the various threads available on drums and barrels, as well as to convert ECO/IBC containers for use with various thread hoses.

Supplier: VICI JOUR RESEARCH

Fiberglass reinforced PP with PP washers. A number of chromatography systems still require or prefer flanged connections. When the tubing is flanged, the washer never comes in contact with the mobile phase.

Supplier: UPCHURCH SCIENTIFIC

VHP Microferrules are made from a proprietary high performance PEEK polymer blend, a material which is unique in its ability to enable the use of capillary tubing in UHPLC environments.

Supplier: OMNIFIT

Flanged tubing system is used for economical low pressure connection. A flanging washer is placed between the flange and the fitting nut. When screwed into a flat-bottom, the flange is compressesed against the bottom of the port to produce a seal.

Supplier: VICI JOUR RESEARCH

PEEK one-piece fingertight fittings. 10-32 threads, for 1/16" tubing. Fingertight up to 350 bar (5000 psi).

Supplier: Restek

Fused silica adapter ferrules are made from valcon polyimide, a unique graphite reinforced composite that is specially made to maximise mechanical stability at temperatures up to 350 °C.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, 1592 Adapter, 1-16 female to 1-8 flat-bottom, female, 1 mm thru-hole, Stainless steel

Supplier: UPCHURCH SCIENTIFIC

This micro injection port adapter assembly can be connected to 360 µm Ext.Ø capillary tubing to introduce samples. It accepts standard 22 gauge Hamilton-style injection syringe needles. The needle butts directly against the connecting tubing during injections, therefore no additional swept volume is added to the fluid pathway by this adapter.

Supplier: VICI JOUR RESEARCH

One-piece hex-head fittings made from PEEK are easy to use with the ValvTool and the Color-It Color-Coded Fingertight adapters. The 10-32 thread is suitable for standard high-pressure female connections. They are available both in a short and long version.

Supplier: UPCHURCH SCIENTIFIC

These PEEK adapters make connections to female ¹/₈" and ¹/₄" National Pipe Thread (NPT) ports.

Supplier: OMNIFIT

Omnifit® threaded adaptors are a useful range of problem solving parts that enable to convert thread sizes quickly and easily, accepting a ¹/₄"-28 UNF male fitting at one end and a range of male and female thread types at the other.