You searched for: Fittings and Connectors

Supplier: Restek

This kit includes a ¹/₄" stainless steel nut and graphite ferrule for attaching the liner to the GC inlet and a ¹/₄ to ¹/₁₆" stainless steel reducer, plus a ¹/₄" and 0,5 mm ID graphite ferrule for attaching the column to the liner.

Supplier: UPCHURCH SCIENTIFIC

Note: Do not use metal fittings in plastic ports, as this can damage the port.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, P-482T-01, flanged nut, ETFE natural, for 1/16" OD tubing, ETFE

Supplier: VICI JOUR RESEARCH

These PP adapters are used for colour coding different solvent lines. They turn ¹/₄" hex-head nuts into fingertight fittings.

Supplier: VICI JOUR RESEARCH

These plugs and caps are used for plugging ports and capping solvent lines.

Supplier: VICI JOUR RESEARCH

Adapter, connects safety exhaust filter to SCAT® waste caps and A.I.T. smart waste caps

Supplier: Restek

These non-reusable column caps increase column lifetime, prevent moisture and air from entering the column during storage.

Supplier: Restek

GRAPHPACK® technology provides a complete system that quickly and reliably makes a leak-tight, low-dead-volume connection.

Supplier: Restek

EXP® reusable fittings for easy and reliable HPLC and UHPLC connections for 10 to 32 fittings and ¹/₁₆" tubing.

Supplier: Restek

These are used to cap off a detector and prevent hydrogen from accidentally diffusing into the oven from an unused detector base.

Supplier: VICI JOUR RESEARCH

PEEK tees and crosses, high pressure, for easy connection of solvent lines.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, P-245, flangeless fitting for 1/16" OD tubing, PFA natural/ETFE blue, 1/4-28 flat-bottom port, standard knurl

Supplier: Restek

Graphite two-piece construction. For Shimadzu 17A, 2010, and 2014 GCs.

Supplier: Restek

These fingertight capillary column nuts rapidly tighten without wrenches and can be used with 0,25, 0,32, or 0,53 mm ID columns.

Supplier: UPCHURCH SCIENTIFIC

These low pressure unions are made from PEEK, ETFE, Delrin or PP.

Supplier: UPCHURCH SCIENTIFIC

These fittings eliminate loosening due to tubing twist.

Supplier: Restek

Internal adapter made of stainless steel gives minimum volume connection from a female pipe fitting on a pressure gauge or regulator to a Valco® zero-dead-volume fitting.

Supplier: UPCHURCH SCIENTIFIC

PEEK or PCTFE.

Supplier: Restek

These nuts are designed for Agilent 5890/6850/6890/7890 GCs. Nuts for use with standard ¹/₁₆" type ferrules are designed to fit a wider variety of ¹/₁₆" ferrules.

Supplier: Restek

These septum nuts are made of high-quality stainless steel and for use with Agilent 5890/6850/6890/7890 split or splitless injectors.

Supplier: Restek

This split or splitless inlet adaptor fitting is suitable for capillary columns with internal diameter 0,53 mm. Makes column installation easy due to the nut protruding farther from the insulated injection port chamber.

Supplier: Restek

This conversion fitting is a flat, soft aluminum sealing ring deforms and butt-seals against the MSD interface. A standard Vespel® ferrule seals the column and 1,59 mm stainless steel nut.

Supplier: Restek

Ferrules with graphite construction for use with packed columns.

Supplier: Restek

Internal tees are made of stainless steel are used to connect three lines. Suitable for 1,6 mm OD tubing.

Supplier: UPCHURCH SCIENTIFIC

PEEK polymer adapters connect peristaltic tubing to standard rigid or semi-rigid tubing.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, U-650, replacement flangeless ferrule, ETFE natural, 1/2-20 flat bottom port, 250 psi, for 1/4" OD tubing, ETFE

Supplier: Restek

Internal uniona are made of 300 series stainless steel with end of tubing that seats squarely at bottoms of fitting details. Suitable for 1,6 mm OD tubing.

Supplier: UPCHURCH SCIENTIFIC

PEEK.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® MicroTight®, F-124H, fitting, micro headless knurl, PEEK blue, 6-32 coned port, for 360 μm OD tubing, 5000 psi, PEEK

Supplier: Cole-Parmer

Cleanroom female Luer to hose barb fittings, straight adapter, ideal for general-purpose, laboratory, and single-use applications to connect tubing with the rest of system.