Supplier: UPCHURCH SCIENTIFIC

ETFE or PEEK.

Supplier: UPCHURCH SCIENTIFIC

PEEK.

Supplier: UPCHURCH SCIENTIFIC

These female M6 adapters are made from PEEK, EFTE or PCTFE.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® NanoTight™, F-142N, ferrules, ETFE natural, 10-32 coned port, for 1/16" OD tubing, 4000 psi, ETFE

Supplier: Restek

CGA-specified nuts and nipples with internal frit, 6,35mm NPT nickel-plated brass.

Supplier: UPCHURCH SCIENTIFIC

Note: Do not use metal fittings in plastic ports, as this can damage the port.

Supplier: Restek

These capillary nuts are made from brass or stainless steel.

Supplier: UPCHURCH SCIENTIFIC

LuerTight™ fittings are designed for connecting fluoropolymer tubing without barbs or nuts. By integrating ferrules into the Luer bodies, these fitting reliably hold tubing in place while giving the convenience of a Luer connection.

Supplier: VICI JOUR RESEARCH

These PEEK adapters connect standard LC fittings to standard LC ports, usable with most common organic and inorganic HPLC solvents without risking corrosion, metal contamination, or protein degradation.

Supplier: KLS Martin Group

Couplings, tubing, Faucet coupling for water jet pump 1/2", Thread: 12,7 mm

Supplier: UPCHURCH SCIENTIFIC

NanoPort™ assemblies provide consistent fluid connections for chip-based analyses, connections will bond to a variety of substrate materials with the use of Loctite™.

Supplier: VICI JOUR RESEARCH

Fiberglass reinforced PP with PP washers. A number of chromatography systems still require or prefer flanged connections. When the tubing is flanged, the washer never comes in contact with the mobile phase.

Supplier: VICI JOUR RESEARCH

These PP adapters are used for colour coding different solvent lines. They turn ¹/₄" hex-head nuts into fingertight fittings.

Supplier: UPCHURCH SCIENTIFIC

VHP Microferrules are made from a proprietary high performance PEEK polymer blend, a material which is unique in its ability to enable the use of capillary tubing in UHPLC environments.

Supplier: OMNIFIT

Flanged tubing system is used for economical low pressure connection. A flanging washer is placed between the flange and the fitting nut. When screwed into a flat-bottom, the flange is compressesed against the bottom of the port to produce a seal.

Supplier: NRG DEVELOPMENTS

These adaptors used to convert the 2" BSP thread to fit the various threads available on drums and barrels, as well as to convert ECO/IBC containers for use with various thread hoses.

Supplier: Bohlender

For connection of sensors with male thread PG to BOLA reactor lids.

Supplier: VICI JOUR RESEARCH

PEEK one-piece fingertight fittings. 10-32 threads, for 1/16" tubing. Fingertight up to 350 bar (5000 psi).

Supplier: UPCHURCH SCIENTIFIC

PP or ETFE. Use these barbed adapters to connect peristaltic-type flexible tubing for general, low pressure applications, such as plumbing Ismatec® peristaltic pumps. Due to the low melting point of PP, these adapters are not autoclavable, however, they can be sterilised via gamma radiation. The ETFE connectors have superiour solvent resistance and a higher temperature rating (80 °C).

Supplier: Restek

Replacement long nut connects stainless steel tubing to a Rheodyne® 6-port valve or other Rheodyne® part.

Supplier: UPCHURCH SCIENTIFIC

Ultra high performance fittings are manufactured from a proprietary PEEK blend (PK) which allow them to be used at higher temperatures (up to 200 °C) and higher pressures.

Supplier: UPCHURCH SCIENTIFIC

These fittings eliminate loosening due to tubing twist.

Supplier: Restek

These nuts are designed for Agilent 5890/6850/6890/7890 GCs. Nuts for use with standard ¹/₁₆" type ferrules are designed to fit a wider variety of ¹/₁₆" ferrules.

Supplier: Restek

These ferrules are made of aluminium eliminate out-gassing and make leak-tight seals for less detector noise. Its unique two-piece design permanently locks on fused silica tubing without causing breakage.

Supplier: UPCHURCH SCIENTIFIC

This micro injection port adapter assembly can be connected to 360 µm Ext.Ø capillary tubing to introduce samples. It accepts standard 22 gauge Hamilton-style injection syringe needles. The needle butts directly against the connecting tubing during injections, therefore no additional swept volume is added to the fluid pathway by this adapter.

Supplier: UPCHURCH SCIENTIFIC

These adapters are made from PEEK or PTFE. Female to male 10-32 to 1/4-28 adapters.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific®, U-650, replacement flangeless ferrule, ETFE natural, 1/2-20 flat bottom port, 250 psi, for 1/4" OD tubing, ETFE

Supplier: Restek

Fused silica adapter ferrules are made from valcon polyimide, a unique graphite reinforced composite that is specially made to maximise mechanical stability at temperatures up to 350 °C.

Supplier: VICI JOUR RESEARCH

Biocompatible PEEK construction. The unique feature of the VICI Jour® column coupler is that it adjusts to fit all 10-32 fitting types. No matter what the fitting type and pilot length – Valco®, Waters®, Upchurch®, Rheodyne®, etc., the coupler adapts to bottom out in the pilot automatically, consequently creating only small void volumes.

Supplier: UPCHURCH SCIENTIFIC

Upchurch Scientific® MicroTight®, F-124H, fitting, micro headless knurl, PEEK blue, 6-32 coned port, for 360 μm OD tubing, 5000 psi, PEEK