You searched for: Chromatography Supplies

Supplier: Agilent

The 4100/4200 Microwave plasma-atomic emission spectrometer runs entirely on air, which means your lab can eliminate flammable and expensive gases. It's safer and more cost efficient than other spectrometers. The 4100/4200 MP-AES enables superior detection and can perform unattended multi-element analyses.

Supplier: Agilent

Agilent uses high-quality graphite and applies stringent quality controls to ensure contamination free and consistency of our contact cylinders for your PerkinElmer graphite furnace AA system. The standard THGA graphite contact cylinders, feature a modified injection port area that helps to minimise condensation and improve analytical performance with difficult matrices. The HGA contact cylinders have shaped graphite contacts to completely encase the graphite tube, ensuring the tube is positioned in a defined environment for uniform radiation conditions.

Supplier: Agilent

Agilent burner chamber assemblies for PerkinElmer AA systems are designed to provide the best precision, efficient drainage, minimal burner blockage, and reduced interferences.

Supplier: Agilent

Capillary column installation kit with diamond-tipped cutting pencil

Supplier: Restek

Use these liners for increased sensitivity.

Supplier: Restek

Inlet liners with deactivation improve trace-level analysis that are suitable for agilent GCs equipped with split/splitless inlets. It is made of borosilicate glass.

Supplier: Restek

Trident direct system can be used to select the right level of protection for analysis. It provides the protection against particulate matter and moderate protection against irreversibly adsorbed compounds.

Supplier: Restek

These FID capillary column adapters made of stainless steel are ideal for PerkinElmer Auto SYS XL.

Supplier: Restek

Liners are used for conversion of ¼" packed injection port.

Supplier: Restek

Installation kit for 1 mm ID columns; for valve applications, Kit contains 1× Valco nut 1,58 mm, 1× stainless steel nut 1,58 mm, 1× Vespel/graphite ferrule 1,58 mm, 1× graphite ferrule 1,58 mm, 1× stainless steel ferrule, 1× stainless steel front ferrule 1,58 mm, 1× stainless steel back ferrule

Supplier: Restek

Carriage motor belt for Agilent 7673A, 7673B and 7673C autosamplers.

Supplier: Restek

Set the column flow rate by injection the methane and optimising linear velocity is preferred method for establishing reproducible retention times.

Supplier: VARIAN

The Merlin Microseal is available in standard and high pressure kits.

Supplier: Agilent

High quality off-axis design ion lenses separate ions from photons and residual neutral material resulting in lower background noise in 7700/8800 ICP-MS systems.

Supplier: Agilent

Clamp kit (includes needle clamp and 2×clamp screw)

Supplier: Agilent

Extended seat capillary for multidraw upgrade kit, 1400 µl

Supplier: Agilent

These coils are equivalent to PerkinElmer ICP-OES coils for complete confidence.

Supplier: Agilent

These alignment interfaces are an integral part of the Agilent diode-array detection system.

Supplier: Restek

Tube made of stainless steel are durable and unconditioned.

Supplier: DOMNICK HUNTER

Maintenance kit 4000 hours for all LC-MS

Supplier: UPCHURCH SCIENTIFIC

These high quality stainless steel sample loops have burr-free, square-cut ends to ensure a flush connection to valve ports.

Supplier: VICI JOUR RESEARCH

These stainless steel 316 sample loops are cut using an electrolytic cutting process followed by ultrasonic and high pressure steam cleaning to remove contaminants, dried and capped with softener free caps to avoid the recontamination of the tubing.

Supplier: UPCHURCH SCIENTIFIC

Use this tubing expanding awl when working with barbed fittings. Sometimes the tubing can be too tight to fit over the barb properly. This awl can also be used with semi-rigid tubing, for those rare applications where this tubing needs to be paired with a barbed fitting. By expanding the int.Ø of the tubing, it will make it an easier process to insert the barbed fitting into place.

Supplier: PEAK SCIENTIFIC

Annual service kit for Genius NM32LA, 1022, 1023

Supplier: Thermo Fisher Scientific

Replacement rotor

Supplier: VICI JOUR RESEARCH

These sample loops are made from PEEK tubing and fittings. Mechanically strong, chemically inert polymer ideal for HPLC applications. Softener-free polyethylene caps are used to avoid contamination of the tubing.

Supplier: OMNIFIT

Universal replacement parts for all Omnifit® labware columns which gives complete flexibility to replace lost or worn parts. Compatible with BenchMark, SolventPlus and HiT column ranges.

Supplier: VICI JOUR RESEARCH

These VICI Jour sample loops are made of high quality stainless steel 316.

Supplier: VICI JOUR RESEARCH

These PEEK sample loops contain no metals or other extractable compounds. Therefore, no foreign materials will be introduced into the system. Softener free PE caps are used to avoid the contamination of the tubing. Particularly suited for separations involving proteins, peptides, nucleic acids or other samples of biological origin as well as in IC systems where metal traces may interact with ionic samples or release transition metals that may deactivate ion exchange columns.

Supplier: Thermo Fisher Scientific

Sample loop, for 9010, 9725 and 9725i injectors, PEEK, 20 µl, For tube I-Ø: 0,25 mm