You searched for: Chromatography Supplies

Supplier: Agilent

Extended seat capillary for multidraw upgrade kit, 1400 µl

Supplier: Agilent

High quality off-axis design ion lenses separate ions from photons and residual neutral material resulting in lower background noise in 7700/8800 ICP-MS systems.

Supplier: Agilent

These alignment interfaces are an integral part of the Agilent diode-array detection system.

Supplier: Agilent

These coils are equivalent to PerkinElmer ICP-OES coils for complete confidence.

Supplier: Restek

This kit contains the tubing and fittings needed to add an additional GC to lab bench.

Supplier: Restek

Frit adaptors

Supplier: Agilent

The Quick-Connect torch module for PerkinElmer ICP-OES includes the torch, mounting block, 2 mm alumina injector, Scott spray chamber, and Cross-Flow nebuliser.

Supplier: Restek

These capillary dedicated FID replacement jet for Agilent 5890/6850/6890/7890 GCs are available in standard, high-temperature or Siltek treated high-performance versions.

Supplier: VARIAN

Load and Lock 4003 column, spare parts kit

Supplier: VARIAN

SPME fibers are available in a range of chemistries, formats, and for use with autosamplers or manual injections.

Supplier: Restek

Z-Belt for use with Agilent 7673B and 7683 autosamplers.

Supplier: Restek

These direct injection glass inserts are suitable for 6,35 mm packed column injection ports.

Supplier: Restek

FID/NPD capillary adapter fitting, high-quality stainless steel, for Agilent 5890/6850/6890 GC's

Supplier: Restek

Flow splitters with fluid resistor technology eliminate the adjustments to the capillary tubing for optimising split ratio with wide range of interchangeable resistors.

Supplier: Restek

Injector mounting post for Agilent 7673 series autosamplers, for use with 6890 GCs

Supplier: Agilent

Loop, 2000 µl, metal, includes two 1/16 stainless steel nuts and two stainless steel ferrules

Supplier: Agilent

Rotor seal, PEEK, for 7010/7000/7040 series

Supplier: Restek

This easy to use adapter fitting is sturdy and made of compact stainless steel.

Supplier: Restek

Autosampler plunger carrier belt for Agilent 7673A and 7673B autosamplers.

Supplier: VARIAN

RheBuild® kits containing genuine Rheodyne® parts are available for most Rheodyne® products. RheBuild® kits eliminate the need to order individual parts.

Supplier: Restek

A complete column packing system which is used to pack the analytical HPLC columns.

Supplier: Agilent

The ISIS 3 dramatically increases the productivity of both the Agilent 7800 ICP-MS and the Agilent 7900 ICP-MS while also allowing high matrix samples to be run for extended periods of time.

Supplier: Agilent

These ion lenses are equivalent to the PerkinElmer ICP-MS versions for complete confidence.

Supplier: Agilent

These coils are equivalent to PerkinElmer ICP-MS coils for complete confidence.

Supplier: Agilent

Filters for PerkinElmer ICP-OES systems.

Supplier: Agilent

The HSDC is comprised of a fused silica cell body and removable capillaries. The light path through the cell is made from black fused silica which significantly minimizes stray light and defines the aperture for the diode-array spectrometer.

Supplier: Restek

This column protection system has three levels of protection: filter only, cartridge only, or filter and cartridge.

Supplier: Restek

These adapters are made of high quality stainless steel.

Supplier: Agilent

These PEEK sample loops are inert to most organic solvents. The stainless-steel sample loops are not interchangeable due to the change in port angle.

Supplier: VARIAN

Solid phase microextraction (SPME) is a technique for extracting analytes from solid, liquid or gaseous samples by adsorbing them onto the SPME fiber and then desorbing them into an inlet, either on a gas chromatograph (GC) or an HPLC system. SPME is amenable to automation using an autosampler or it can be performed manually as well.