You searched for: Chromatography Supplies

Supplier: Restek

Replacement desiccant cartridge

Supplier: Restek

Installation Kit for 2 mm ID columns; for valve applications, Kit contains 1× stainless steel nut 3,2 mm, 1× stainless steel Valco nut, 1× Vespel/graphite ferrule 3,2 mm, 1× stainless steel Valco ferrule 3,2 mm, 1× stainless steel front ferrule 3,2 mm, 1× stainless steel back ferrule 3,2 mm

Supplier: Agilent

These sample loops are fully compatible with your PerkinElmer FIMS/FIAS systems, so can be confident that they will integrate seamlessly with PerkinElmer AA system.

Supplier: Agilent

These supplies can enhance the performance and productivity of PerkinElmer spectroscopy systems.

Supplier: Restek

Inlet maintenance kit for use with Agilent GCs.

Supplier: Restek

The UHP pulse dampener made up of stainless steel fluid path.

Supplier: Agilent

All the parts required to connect solvent bottles to your HPLC instrument.

Supplier: Agilent

The kit contains needles, ferrule and a needle holder.

Supplier: Agilent

A vacuum degasser is recommended for maximum sensitivity in the low UV wavelength range; high injection precision; high retention time reproducibility; and flow rates below 0,5 ml/min.

Supplier: Restek

Inlet liners with deactivation improve trace-level analysis that are suitable for agilent GCs equipped with split/splitless inlets. It is made of borosilicate glass.

Supplier: Restek

These kits are used for start-up and maintenance in all HPLC systems.

Supplier: Restek

Use these liners for increased sensitivity. They are manufactured from borosilicate glass or metal.

Supplier: Restek

Direct injection Uniliner® liners minimise solvent and peak tailing. These are suitable for 6,35 mm packed column injection ports.

Supplier: Restek

Replacement parts for Shimadzu HPLC systems.

Supplier: Restek

Uniliner® liners must be used with a Uniliner® liner adaptor for ¹/₄" injection ports.

Supplier: Restek

This reservoir kit is used to restore the performance of bonded-phase capillary columns by dissolving and removing soluble, nonvolatile residue. The rinsing reservoir is equipped with 6,4 mm inlet and outlet connections and includes a built-in fritted disk to prevent particulate matter from contaminating the column.

Supplier: Restek

Packed column inlet adapter kits center columns perfectly in 6,35 mm injection ports to eliminate bent syringe needles.

Supplier: Agilent

The mixing/separation assembly is a perfect match for your PerkinElmer FIMS/FIAS system.

Supplier: Agilent

These performance maintenance kits for Dionex HPLC systems contain all the normal wear parts, tools for disassembly/reassembly, and instructions necessary to keep your systems operating at peak performance.

Supplier: Agilent

Agilent burner chamber assemblies for PerkinElmer AA systems are designed to provide the best precision, efficient drainage, minimal burner blockage, and reduced interferences.

Supplier: Agilent

These graphite platforms and tubes for PerkinElmer graphite furnace AA systems are quality tested to ensure every batch passes our demanding performance specifications for contamination, sensitivity, precision, electrical resistance, and lifetime.

Supplier: Restek

These injector adapters made of stainless steel are ideal for PerkinElmer CAP injector.

Supplier: Restek

This column protection system has three levels of protection: filter only, cartridge only, or filter and cartridge.

Supplier: Restek

These adapters are made of high quality stainless steel.

Supplier: Agilent

These PEEK sample loops are inert to most organic solvents. The stainless-steel sample loops are not interchangeable due to the change in port angle.

Supplier: VARIAN

Solid phase microextraction (SPME) is a technique for extracting analytes from solid, liquid or gaseous samples by adsorbing them onto the SPME fiber and then desorbing them into an inlet, either on a gas chromatograph (GC) or an HPLC system. SPME is amenable to automation using an autosampler or it can be performed manually as well.

Supplier: Restek

These Vu-tight Direct injection (DI) liners are suitable for 6,35 mm packed injection port conversion. They are available in two designs and fit 0,32 and 0,53 mm ID capillary columns (column outer diameter from 0,5 mm to 0,8 mm).

Supplier: Restek

For use with Parker Balston® zero air generators.

Supplier: Restek

These capillary dedicated FID replacement jet for Agilent 5890/6850/6890 GCs are available in standard, high-temperature or Siltek treated high-performance versions.

Supplier: Restek

The oven sensors works in conjunction with the oven control board to regulate oven temperature.