You searched for: Fittings and Connectors

Supplier: Restek

This conversion fitting is a flat, soft aluminum sealing ring deforms and butt-seals against the MSD interface. A standard Vespel® ferrule seals the column and 1,59 mm stainless steel nut.

Supplier: VARIAN

PEEK fittings resists pressure up to 5000 psi and temperature of 100 °C.

Supplier: Restek

This Swagelok® fitting kits includes the most common assortment of ¹/₈" and ¹/₄" brass fittings.

Supplier: Restek

Parker® (A-Lok) fittings are ideal for installing new equipment, modifying existing instrumentation, or replacing worn connections. Fittings are available in brass or 316 grade stainless steel.

Supplier: Restek

These nuts are designed for Agilent 5890/6850/6890/7890 GCs. Nuts for use with standard ¹/₁₆" type ferrules are designed to fit a wider variety of ¹/₁₆" ferrules.

Supplier: Agilent

These connectors are equivalent to the PerkinElmer AA versions, so you can be confident that they will integrate seamlessly with your PerkinElmer AA system.

Supplier: Restek

These fingertight capillary column nuts rapidly tighten without wrenches and can be used with 0,25, 0,32, or 0,53 mm ID columns.

Supplier: Restek

EXP® reusable fittings for easy and reliable HPLC and UHPLC connections for 10 to 32 fittings and ¹/₁₆" tubing.

Supplier: Restek

These non-reusable column caps increase column lifetime, prevent moisture and air from entering the column during storage.

Supplier: Restek

Swagelok®, Reducing union, 1/4" to 1/16", Stainless steel

Supplier: Restek

GRAPHPACK® technology provides a complete system that quickly and reliably makes a leak-tight, low-dead-volume connection.

Supplier: VARIAN

Bond Elut adapters fit on top of any Bond Elut cartridge and contain a female Luer fitting that accommodates the tip of another cartridge.

Supplier: GLASWARENFABRIK KARL HECHT

Assembly kit for filtering flasks, with removable plastic hose connection, short and long screw and seals.

Supplier: Restek

These septum nuts are made of high-quality stainless steel and for use with Agilent 5890/6850/6890/7890 split or splitless injectors.

Supplier: Restek

CGA-specified nuts and nipples with internal frit, 6,35mm NPT nickel-plated brass.

Supplier: Restek

Internal tees are made of stainless steel are used to connect three lines. Suitable for 1,6 mm OD tubing.

Supplier: Restek

These capillary nuts are made from brass or stainless steel.

Supplier: Restek

Internal uniona are made of 300 series stainless steel with end of tubing that seats squarely at bottoms of fitting details. Suitable for 1,6 mm OD tubing.

Supplier: Restek

Internal adapter made of stainless steel gives minimum volume connection from a female pipe fitting on a pressure gauge or regulator to a Valco® zero-dead-volume fitting.

Supplier: Restek

This split or splitless inlet adaptor fitting is suitable for capillary columns with internal diameter 0,53 mm. Makes column installation easy due to the nut protruding farther from the insulated injection port chamber.

Supplier: Restek

These ferrules are made of aluminium eliminate out-gassing and make leak-tight seals for less detector noise. Its unique two-piece design permanently locks on fused silica tubing without causing breakage.

Supplier: Restek

Ferrules with graphite construction for use with packed columns.

Supplier: Restek

Fused silica adapter ferrules are made from valcon polyimide, a unique graphite reinforced composite that is specially made to maximise mechanical stability at temperatures up to 350 °C.

Supplier: Restek

These internal cross are made of stainless steel. Used to connect four lines. Ideal for 1,6 mm OD tubing.

Supplier: Agilent

Agilent adapters are equivalent to the PerkinElmer FIMS/FIAS versions, so you can be confident that they will integrate seamlessly with your PerkinElmer AA system.

Supplier: EDWARDS HIGH VACUUM METTLER

Reducing cross, stainless steel, 130 mm, DN 40/25, Stainless steel

Supplier: Restek

Replacement long nut connects stainless steel tubing to a Rheodyne® 6-port valve or other Rheodyne® part.

Supplier: Agilent

UltiMetal Plus, Flexible metal ferrule, for UltiMetal column tubing, Metal, Hole Ø: - mm, Tubing int.Ø: 0,53 mm

Supplier: Restek

These finger-tight capillary column nuts made from high-quality stainless steel are an alternative to conventional column nuts. These fittings work best with graphite type ferrules and help prevent over tightening, which can cause graphite material to exude into the inlet.

Supplier: Restek

Internal reducing union used to connect two sizes of tubing, using zero-dead-volume fittings on each end. Suitable for 1,6 to 3,2 mm OD tubing.